ECM INSTALLATION


  1. INSTALL ECM


    1. A01IR2RE01

      Install the 2 brackets to the ECM with the 4 screws.

      Torque:
      3.0 N*m  { 31 kgf*cm, 27 in.*lbf }
    2. A01IPHW

      Install the ECM with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    3. Connect the 2 ECM connectors.


      1. A01IN5H

        Connect the 2 ECM connectors and lower the 2 levers.

        Note


        • When connecting the connectors, make sure that dirt, water or other foreign matter does not get caught between the connectors and other parts.

        • Make sure that the 2 levers are securely lowered.

    4. A01IQY7

      for Manual Transaxle:

      Connect the wire harness clamp.

  2. CONNECT NO. 2 AIR CLEANER INLET


    1. A01IT65

      Connect the No. 2 air cleaner inlet to the vehicle body with the bolt.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

  3. INSTALL NO. 1 AIR CLEANER INLET


    1. A01IPHO

      Attach the 2 claws to install the No. 1 air cleaner inlet.

    2. Install the clip.

  4. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    1. A01IQF0

      Install the air cleaner case with the 3 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    2. Attach the wire harness clamp to the air cleaner case.

  5. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

  6. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    1. A01IPUC

      Connect the air cleaner cap with the band.

    2. Connect the PCV hose.

    3. A01IP4V

      Connect the 2 clamps.

    4. A01ISEG

      Attach the 2 clamps and connect the wire harness.

    5. Connect the mass air flow meter connector.

  7. INSTALL NO. 2 CYLINDER HEAD COVER


    1. A01IRS7

      Attach the 4 clips to install the cover.

      Note


      • Be sure to attach the clips securely.

      • Do not apply excessive force or hit the cover to attach the clips. This may cause the cover to break.

  8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  9. INSTALL RADIATOR SUPPORT OPENING COVER


    1. A01IQMS

      Attach the 4 hooks to install the radiator support opening cover.

    2. Install the 3 clips.

  10. PERFORM INITIALIZATION

    Note


    • Be sure to perform this procedure after reassembling the throttle body or removing and reinstalling any throttle body component.

    • Perform the following procedure after replacing the ECM, throttle body or any throttle body components. The following procedure should also be performed if the throttle body is cleaned.

    • Be sure to perform this procedure after replacing the ECM and reconnecting the battery cable.


    1. Disconnect the EFI MAIN and ETCS fuses at the same time. Wait at least 60 seconds, and then reconnect the fuses.

    2. Turn the ignition switch to ON without operating the accelerator pedal.

      Note

      If the accelerator pedal is operated, perform the above steps again.

    3. Connect the intelligent tester to the DLC3 and clear the DTCs Click here.

    4. Start the engine and check that the MIL is not illuminated and that the idle speed is within the specified range when the A/C is switched off after the engine is warmed up.

      Standard Idle Speed
      Item Specified Condition
      for Manual Transaxle 580 to 680 rpm
      for CVT 600 to 700 rpm

      Note


      • Be sure to perform this step with all accessories off.

      • Make sure that the shift lever is in neutral (for Manual Transaxle), or N or P (for CVT).

    5. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Sensor Position. Fully depress the accelerator pedal and check that the value is 60% or more.

    6. Perform a road test and confirm that there are no abnormalities.

  11. RESET MEMORY (for CVT)


    1. When replacing the ECM, perform the Reset Memory procedure (initialization) Click here.