REAR DOOR BELT MOULDING INSTALLATION


  1. INSTALL REAR DOOR BELT MOULDING ASSEMBLY


    1. A01NN1Y

      Engage the 5 claws to install the rear door belt moulding assembly.

  2. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. Connect the cable to the negative (-) battery terminal and the rear power window regulator motor connector.

    2. Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.


      1. w/ Navigation System for HDD:

        Note

        After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

        Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
        Specification Waiting Time
        w/o Telematics transceiver 60 sec.
        w/ Telematics transceiver 120 sec.

    3. Disconnect the power window regulator switch assembly and rear power window regulator motor connector.

    4. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system Click here.

    5. A01NKD7E01

      Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as indicated by the arrows in the order shown in the illustration.

    6. A01NK7YE01

      Install the rear door glass sub-assembly with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Tech Tips

      Tighten the bolts in the order shown in the illustration.

  3. INSTALL REAR DOOR REAR GUIDE SEAL


    1. A01NLBT

      Install the rear door rear guide seal with the 2 screws.

  4. INSTALL REAR DOOR WINDOW REAR GUIDE SUB-ASSEMBLY


    1. Install the temporary screw to the rear door window division bar sub-assembly.

    2. A01NN6GE01
      Text in Illustration
      *1 Temporary Screw

      Engage the claw, guide and temporarily install the rear door window rear guide sub-assembly.

    3. Install the bolt and screw.

    4. Tighten the temporary screw to install the rear door window rear guide sub-assembly.

  5. INSTALL REAR DOOR VENT SEAL


    1. A01NIKB

      Install the rear door vent seal.

  6. INSTALL REAR DOOR GLASS RUN


    1. A01NJI4

      Install the rear door glass run.

  7. CONNECT REAR DOOR WEATHERSTRIP


    1. A01NMF2

      Engage the clip and connect the rear door weatherstrip.

  8. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the rear door panel.

    2. A01NM9SE01
      Text in Illustration
      *1 Reference Point

      Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.

    3. Attach the rear door service hole cover according to the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover preventing wrinkles and air bubbles.

    4. Connect the 2 connectors.

  9. INSTALL REAR DOOR TRIM BRACKET


    1. A01NIN8

      Install the rear door trim bracket with the 2 screws.

  10. INSTALL REAR DOOR FRAME GARNISH


    1. A01NJBB

      Engage the clip to install the rear door frame garnish.

    2. Install the 2 clips.

  11. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    1. A01NN5Z

      Engage the 4 claws and install the rear door inner glass weatherstrip as shown in the illustration.

  12. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. Install 2 new rear door trim board retainers (green).

    2. A01NL2H

      Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

    3. for 12 Speakers or 15 Speakers:


      1. Connect the connector.

    4. A01NLCQ

      Engage the rear door trim board sub-assembly with the 4 claws of the rear door inner glass weatherstrip as shown in the illustration.

    5. A01NMVRE02
      Text in Illustration
      *1 Rear Door Trim Board Retainer

      Engage the 7 clips, 2 rear door trim board retainers and install the rear door trim board sub-assembly.

    6. Install the 3 screws.

  13. INSTALL COURTESY LIGHT ASSEMBLY


    1. Connect the connector.

    2. A01NM7YE02
      Text in Illustration
      *A for LH Side
      *B for RH Side

      Engage the claw to install the courtesy light assembly.

  14. INSTALL REAR DOOR ARMREST COVER


    1. A01NLZS

      Install the rear door armrest cover.

  15. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. Connect the connector.

    2. A01NLIX

      Engage the 2 clips and 3 claws, and install the rear power window regulator switch assembly with rear door armrest base panel.

  16. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A01NMF5

      Engage the 3 claws and install the rear door inside handle bezel plug.

  17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  18. INSTALL REAR DECK FLOOR BOX


    1. A01NIBL

      Install the rear deck floor box with the 3 clips.

  19. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here