POWER MIRROR CONTROL SYSTEM Power Retractable Mirrors do not Operate with Power Retract Mirror Switch

SYSTEM DESCRIPTION

The main body ECU (multiplex network body ECU) receives the outer mirror retract switch signal from the multiplex network master switch assembly via LIN communication. The main body ECU then sends the mirror retract/return signal to each outer mirror control ECU via CAN communication. Based on the signal, each outer mirror control ECU retracts or returns the outer rear view mirror assembly.

INSPECTION PROCEDURE

PROCEDURE

1. Click here

   CHECK CAN COMMUNICATION SYSTEM

   
   

   1. Use the intelligent tester to check if the CAN communication system is functioning normally (Click here).

      OK
      CAN communication DTC is not output.

   
   
   • OKClick here
   • NGClick here
2. Click here

   CHECK LIN COMMUNICATION SYSTEM

   
   

   1. Use the intelligent tester to check if the LIN communication system is functioning normally (Click here).

      OK
      LIN communication DTC is not output.

   
   
   • OKClick here
   • NGClick here
3. Click here

   READ VALUE USING INTELLIGENT TESTER (OUTER MIRROR RETRACT SWITCH)

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the intelligent tester on.

   4. Enter the following menus: Body / Master Switch / Data List.

   5. Read the Data List according to the display on the intelligent tester.

      Table 1. Master Switch

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      Outer Mirror Fold SW	Mirror retract switch signal / ON or OFF	ON: Retract switch in retract position OFF: Retract switch in driving position	-

      OK
      On the intelligent tester screen, ON or OFF is displayed for each item according to the above.

   
   
   • OKClick here
   • NGClick here
4. Click here

   PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MIRROR RETRACT FUNCTION)

   
   

   1. Enter the following menus: Body / Mirror L or Mirror R / Active Test.

   2. Perform the Active Test according to the display on the intelligent tester.

      Table 2. Mirror L / Mirror R

      Tester Display	Test Part	Control Range	Diagnostic Note
      Mirror Fold/Return	Mirror retract operation	ON / OFF	-

      Result
      Result Proceed to Outer rear view mirror assemblies operate normally A Outer rear view mirror assembly RH does not operate normally B Outer rear view mirror assembly LH does not operate normally C

   
   
   • AClick here
   • BClick here
   • CClick here
5. Click here

   REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

   
   

   1. Replace main body ECU (multiplex network body ECU) (Click here).

   
   
   • NEXTClick here
6. Click here

   CHECK POWER RETRACT MIRROR FUNCTION

   
   

   1. Check power retract mirror function (manual function) (Click here).

      OK
      Power retract mirror function (manual function) is normal.

   
   
   • OKClick here
   • NGClick here
7. Click here

   INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

   
   
   1. 

      Remove the outer rear view mirror assembly RH (Click here).

   2. When checking each mirror position, set the mirror position by hand. Apply auxiliary battery voltage and check the mirror movement.

      Note:
      

      • Disconnect and reconnect the auxiliary battery for each mirror position check.

      • The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

      OK

      Measurement Condition Mirror Position Specified Condition Auxiliary battery positive (+) → Terminal z3-3 (MR+) Auxiliary battery negative (-) → Terminal z3-11 (MR-) Forward position (A) Moves from (A) to retracted position (E) Auxiliary battery negative (-) → Terminal z3-3 (MR+) Auxiliary battery positive (+) → Terminal z3-11 (MR-) Forward position (A) Does not move Auxiliary battery positive (+) → Terminal z3-3 (MR+) Auxiliary battery negative (-) → Terminal z3-11 (MR-) Between forward position (A) and driving position (C) Moves from (B) to retracted position (E) Auxiliary battery negative (-) → Terminal z3-3 (MR+) Auxiliary battery positive (+) → Terminal z3-11 (MR-) Between forward position (A) and driving position (C) Moves from (B) to forward position (A) Auxiliary battery positive (+) → Terminal z3-3 (MR+) Auxiliary battery negative (-) → Terminal z3-11 (MR-) Driving position (C) Moves from (C) to retracted position (E) Auxiliary battery negative (-) → Terminal z3-3 (MR+) Auxiliary battery positive (+) → Terminal z3-11 (MR-) Driving position (C) Does not move Auxiliary battery positive (+) → Terminal z3-3 (MR+) Auxiliary battery negative (-) → Terminal z3-11 (MR-) Between driving position (C) and retracted position (E) Moves from (D) to retracted position (E) Auxiliary battery negative (-) → Terminal z3-3 (MR+) Auxiliary battery positive (+) → Terminal z3-11 (MR-) Between driving position (C) and retracted position (E) Moves from (D) to driving position (C) Auxiliary battery positive (+) → Terminal z3-3 (MR+) Auxiliary battery negative (-) → Terminal z3-11 (MR-) Retracted position (E) Does not move Auxiliary battery negative (-) → Terminal z3-3 (MR+) Auxiliary battery positive (+) → Terminal z3-11 (MR-) Retracted position (E) Moves from (E) to driving position (C)

   
   
   • OKClick here
   • NGClick here
8. Click here

   INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

   
   
   1. 

      Remove the outer rear view mirror assembly LH (Click here).

   2. When checking each mirror position, set the mirror position by hand. Apply auxiliary battery voltage and check the mirror movement.

      Note:
      

      • Disconnect and reconnect the auxiliary battery for each mirror position check.

      • The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

      OK

      Measurement Condition Mirror Position Specified Condition Auxiliary battery positive (+) → Terminal z4-3 (MR+) Auxiliary battery negative (-) → Terminal z4-11 (MR-) Forward position (A) Moves from (A) to retracted position (E) Auxiliary battery negative (-) → Terminal z4-3 (MR+) Auxiliary battery positive (+) → Terminal z4-11 (MR-) Forward position (A) Does not move Auxiliary battery positive (+) → Terminal z4-3 (MR+) Auxiliary battery negative (-) → Terminal z4-11 (MR-) Between forward position (A) and driving position (C) Moves from (B) to retracted position (E) Auxiliary battery negative (-) → Terminal z4-3 (MR+) Auxiliary battery positive (+) → Terminal z4-11 (MR-) Between forward position (A) and driving position (C) Moves from (B) to forward position (A) Auxiliary battery positive (+) → Terminal z4-3 (MR+) Auxiliary battery negative (-) → Terminal z4-11 (MR-) Driving position (C) Moves from (C) to retracted position (E) Auxiliary battery negative (-) → Terminal z4-3 (MR+) Auxiliary battery positive (+) → Terminal z4-11 (MR-) Driving position (C) Does not move Auxiliary battery positive (+) → Terminal z4-3 (MR+) Auxiliary battery negative (-) → Terminal z4-11 (MR-) Between driving position (C) and retracted position (E) Moves from (D) to retracted position (E) Auxiliary battery negative (-) → Terminal z4-3 (MR+) Auxiliary battery positive (+) → Terminal z4-11 (MR-) Between driving position (C) and retracted position (E) Moves from (D) to driving position (C) Auxiliary battery positive (+) → Terminal z4-3 (MR+) Auxiliary battery negative (-) → Terminal z4-11 (MR-) Retracted position (E) Does not move Auxiliary battery negative (-) → Terminal z4-3 (MR+) Auxiliary battery positive (+) → Terminal z4-11 (MR-) Retracted position (E) Moves from (E) to driving position (C)

   
   
   • OKClick here
   • NGClick here
9. Click here

   GO TO CAN COMMUNICATION SYSTEMClick here

10. Click here

    GO TO LIN COMMUNICATION SYSTEMClick here

11. Click here

    REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLYClick here

12. Click here

    REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLYClick here

13. Click here

    END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

14. Click here

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RHClick here

15. Click here

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER SIDE)Click here

16. Click here

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LHClick here

17. Click here

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER SIDE)Click here