Click here

REAR DOOR ADJUSTMENT

Click here
Click here Click here
CAUTION:

Before adjusting the door positions of vehicles equipped with side and curtain shield airbags, be sure to disconnect the battery. After adjustment, check that the SRS warning light is operating normally and there are no SRS DTCs output.

Tip:

  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

  • Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

  • Specified torque for standard bolts is shown in the standard bolt chart (Click here).

Click here
  1. Click here

    INSPECT REAR DOOR


    1. A01NLNCE01

      Check that the clearance measurements of areas *1 through *25 are within each standard range.

      Table 1. Standard Clearance
      Area Measurement Area Measurement
      *1 3.0 to 6.0 mm (0.118 to 0.236 in.) *2 -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
      *3 5.5 mm (0.217 in.) *4 -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
      *5 3.5 to 6.5 mm (0.138 to 0.256 in.) *6 0.5 to 3.5 mm (0.0197 to 0.138 in.)
      *7 3.5 to 6.5 mm (0.138 to 0.256 in.) *8 0.6 to 3.6 mm (0.0236 to 0.142 in.)
      *9 3.5 to 6.5 mm (0.138 to 0.256 in.) *10 1.9 to 4.9 mm (0.0748 to 0.193 in.)
      *11 5.0 to 8.0 mm (0.197 to 0.315 in.) *12 5.0 to 8.0 mm (0.197 to 0.315 in.)
      *13 2.8 to 5.8 mm (0.110 to 0.228 in.) *14 -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
      *15 5.5 to 10.5 mm (0.217 to 0.413 in.) *16 5.5 to 10.5 mm (0.217 to 0.413 in.)
      *17 3.0 to 7.0 mm (0.118 to 0.276 in.) *18 3.2 to 6.2 mm (0.126 to 0.244 in.)
      *19 -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) *20 3.2 to 6.2 mm (0.126 to 0.244 in.)
      *21 -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) *22 3.2 to 6.2 mm (0.126 to 0.244 in.)
      *23 -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) *24 3.0 to 6.0 mm (0.118 to 0.236 in.)
      *25 -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) - -
  2. Click here

    REMOVE REAR DECK FLOOR BOX


    1. A01NIBL

      Remove the 3 clips and the rear deck floor box.

  3. Click here

    PRECAUTION (w/ Navigation System for HDD)

    Note:

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Table 2. Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.
  4. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system (Click here).

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  5. Click here

    ADJUST REAR DOOR


    1. A01NNED

      Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

      09812-00010

    2. Tighten the hinge bolts on the vehicle body after the adjustment.

      26 N*m 265 kgf*cm 19 ft.*lbf

    3. Loosen the hinge bolts on the door and adjust the door position.

    4. Tighten the hinge bolts on the door after the adjustment.

      27 N*m 275 kgf*cm 20 ft.*lbf
    5. A01NL4CE01

      Using a screwdriver, disengage the 4 claws and remove door lock striker cover.

      Table 3. Text in Illustration
      *1 Protective Tape
      Tip:

      Tape the screwdriver tip before use.

    6. A01NIGA

      Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.

    7. Using a brass bar and a hammer, hit the striker to adjust its position.

    8. Using a T40 "TORX" socket wrench, tighten the striker mounting screws after the adjustment.

      23 N*m 235 kgf*cm 17 ft.*lbf
    9. A01NL8L

      Engage the 4 claws and install the door lock striker cover.

  6. Click here

    CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  7. Click here

    INSTALL REAR DECK FLOOR BOX


    1. A01NIBL

      Install the rear deck floor box with the 3 clips.

  8. Click here

    INSPECT SRS WARNING LIGHT

    (Click here)