POWER WINDOW REGULATOR MOTOR (for Front Door) INSTALLATION

INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY

1. Apply MP grease to the sliding parts of the front door window regulator assembly.

2. Install the temporary bolt to the front door window regulator assembly.

3. 

   Temporarily install the front door window regulator assembly.

   Table 1. Text in Illustration

   *1	Temporary Bolt

4. Tighten the temporary bolt and 5 bolts to install the front door window regulator assembly.

   Tip:

   Tighten the bolts in the order shown in the illustration.

   8.0 N*m

   82 kgf*cm

   71 in.*lbf

5. Connect the connector.

INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

1. Connect the cable to the negative (-) battery terminal.

2. Connect the power window regulator master switch assembly and move the front door glass subassembly so that the door glass bolts can be seen.

   
   

   1. w/ Navigation System for HDD:

      Note:

      After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

      Table 2. Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal

      Specification	Waiting Time
      w/o Telematics transceiver	60 sec.
      w/ Telematics transceiver	120 sec.

3. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

   CAUTION:

   Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system (Click here).

4. 

   Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows in the order shown in the illustration.

5. 

   Install the front door glass sub-assembly with the 2 bolts.

   5.5 N*m

   56 kgf*cm

   49 in.*lbf

   Tip:

   Tighten the bolts in the order shown in the illustration.

INSTALL FRONT DOOR SERVICE HOLE COVER

1. Apply butyl tape to the front door panel.

2. 

   Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.

   Table 3. Text in Illustration

   *1	Reference Point

3. Attach the front door service hole cover according to the reference points on the front door panel.

   Note:

   Securely install the front door service hole cover preventing wrinkles and air bubbles.

4. Connect the connector.

INSTALL NO. 1 FRONT DOOR TRIM BRACKET

1. 

   Install the 2 bolts and No. 1 front door trim bracket.

INSTALL FRONT NO. 3 SPEAKER ASSEMBLY

1. Engage the clip and temporarily install the front No. 3 speaker assembly.

2. Install the front No. 3 speaker assembly with the 2 screws.

3. Connect the connector.

INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP

1. 

   Engage the 4 claws and install the front door inner glass weatherstrip as shown in the illustration.

INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

1. Install a new front door trim board retainer (green).

2. 

   Connect the front door lock remote control cable assembly and front door inside locking cable assembly.

3. Connect each connector.

4. 

   Engage the front door trim board sub-assembly with the 4 claws of the front door inner glass weatherstrip as shown in the illustration.

5. 

   Engage the 10 clips, front door trim board retainer and install the front door trim board sub-assembly.

   Table 4. Text in Illustration

   *1	Front Door Trim Board Retainer

6. Install the 3 screws.

   (A)
   3.5 N*m	36 kgf*cm	31 in.*lbf

INSTALL NO. 1 FRONT DOOR STIFFENER CUSHION

1. 

   Install the No. 1 front door stiffener cushion with the screw.

INSTALL COURTESY LIGHT ASSEMBLY

1. Connect the connector.

2. 

   Engage the claw to install the courtesy light assembly.

   Table 5. Text in Illustration

   *A	for LH Side
   *B	for RH Side

INSTALL DOOR ARMREST COVER

1. 

   Install the door armrest cover.

INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

1. 

   Connect the connector.

2. Engage the 2 clips and 5 claws, and install the power window regulator master switch assembly with front door armrest base panel.

INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

1. 

   Connect the connector.

2. Engage the 2 clips and 5 claws, and install the power window regulator switch assembly with front door armrest base panel.

INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

1. 

   Engage the 3 claws and install the front door inside handle bezel plug.

INSTALL REAR DECK FLOOR BOX

1. 

   Install the rear deck floor box with the 3 clips.