Click here

BACK DOOR GLASS REMOVAL

Click here
Click here Click here
Tip:

The back door glass can be reused. If any clip of the back door glass is broken, use butyl tape to support the glass until the applied adhesive hardens when reinstalling the back door glass.

Click here
  1. Click here

    REMOVE UPPER BACK WINDOW PANEL TRIM


    1. A01NMCGE01

      Disengage the 7 clips and 6 claws, and remove the upper back window panel trim.

      Table 1. Text in Illustration
      *1 2-piece Type Clip
      Tip:

      If any clips remain on the back door panel after the upper back window panel trim is removed, remove the clips and install them to the upper back window panel trim.

  2. Click here

    REMOVE TONNEAU COVER SUB-ASSEMBLY

  3. Click here

    REMOVE BACK DOOR FINISH COVER LH (w/o Power Back Door)


    1. A01NLIM

      Using a moulding remover, disengage the 6 claws and remove the back door finish cover LH.

  4. Click here

    REMOVE BACK DOOR TRIM BASE (w/ Power Back Door)


    1. A01NMQF

      Using a moulding remover, disengage the 4 claws and remove the back door trim base.

  5. Click here

    REMOVE BACK DOOR FINISH COVER RH (w/o Power Back Door)


    1. A01NKTM

      Using a moulding remover, disengage the 6 claws and remove the back door finish cover RH.

  6. Click here

    REMOVE DOOR PULL HANDLE WITH SWITCH (w/ Power Back Door)


    1. A01NM4O

      Using a moulding remover, disengage the 6 claws and remove the door pull handle with switch.

    2. Disconnect the connector.

  7. Click here

    REMOVE BACK DOOR LOCK COVER


    1. A01NLEF

      Disengage the 4 claws and remove the back door lock cover.

  8. Click here

    REMOVE NO. 2 ROOM LIGHT ASSEMBLY


    1. A01NMGHE01

      Using a screwdriver wrapped with protective tape, disengage the claw.

      Table 2. Text in Illustration
      *1 Protective Tape

    2. Disconnect the connector and remove the No. 2 room light assembly.

  9. Click here

    REMOVE BACK DOOR UPPER TRIM COVER LH


    1. A01NMXSE01

      Using a screwdriver, disengage the 2 claws and remove the back door upper trim cover LH as shown in the illustration.

      Tip:

      Tape the screwdriver tip before use.

      Table 3. Text in Illustration
      *1 Protective Tape
  10. Click here

    REMOVE BACK DOOR UPPER TRIM COVER RH


    1. A01NLUPE01

      Using a screwdriver, disengage the 2 claws and remove the back door upper trim cover RH as shown in the illustration.

      Tip:

      Tape the screwdriver tip before use.

      Table 4. Text in Illustration
      *1 Protective Tape
  11. Click here

    REMOVE BACK DOOR SERVICE HOLE COVER LH


    1. A01NLZM

      Disengage the 5 claws and remove the back door service hole cover LH.

  12. Click here

    REMOVE BACK DOOR SERVICE HOLE COVER RH


    1. A01NI3K

      Disengage the 5 claws and remove the back door service hole cover RH.

  13. Click here

    REMOVE BACK DOOR TRIM PANEL ASSEMBLY


    1. A01NLCM

      Remove the 2 screws.

    2. A01NLV2E01

      Grab the service holes by hand.

      Note:

      Make sure to hold the clip bases as shown in the illustration.

    3. Pull the back door trim panel assembly in the direction shown by the arrows in the illustration (pull perpendicular to the surface of the trim panel) to disengage the 2 claws and 16 clips, and remove the back door trim panel assembly.

      Table 5. Text in Illustration
      *1 2-piece Type Clip
      Note:

      Removing the back door trim panel assembly at an angle may cause deformation or damage. To avoid this, make sure to pull the panel in the direction shown by the arrows (pull perpendicular to the surface of the panel).

      Tip:

      If any clips remain on the back door panel after the back door trim panel assembly is removed, remove the clips and install them to the back door trim panel assembly.

  14. Click here

    REMOVE BACK DOOR TRIM COVER LH


    1. A01NNDQ

      Disengage the 3 clips and remove the back door trim cover LH.

  15. Click here

    REMOVE BACK DOOR TRIM COVER RH


    1. A01NJY9

      Disengage the 3 clips and remove the back door trim cover RH.

  16. Click here

    REMOVE REAR SPOILER SUB-ASSEMBLY


    1. Disconnect each connector.

    2. A01NLW9

      Remove the 2 hole plugs.

    3. Remove the 5 nuts.

    4. A01NKCQ

      Disengage the clip and 2 pins to remove the rear spoiler sub-assembly.

    5. Remove the clip and 2 pins.

  17. Click here

    REMOVE REAR WIPER ARM AND BLADE ASSEMBLY


    1. A01NI7N

      Remove the nut and the rear wiper arm and blade assembly.

  18. Click here

    REMOVE BACK DOOR GLASS


    1. A01NN9I

      Disengage the 2 clamps.

    2. Disconnect the 3 connectors.

    3. A01NL7VE01

      Apply protective tape to the outer surface of the vehicle body to prevent scratches.

      Table 6. Text in Illustration
      *1 Protective Tape
      Note:

      When separating the back door glass from the vehicle, be careful not to damage the paint or interior and exterior ornaments.

    4. A01NMGNE01

      Pass a piano wire between the vehicle body and back door glass from the interior, as shown in the illustration.

      Table 7. Text in Illustration
      *1 Protective Tape

    5. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

    6. Cut off the adhesive by pulling the piano wire around the back door glass.

      Note:

      Leave as much adhesive on the vehicle body as possible when removing the back door glass.

    7. A01NN8HE01

      Place matchmarks on the back door glass and vehicle body on the locations indicated in the illustration.

      Table 8. Text in Illustration
      *1 Matchmark
      Tip:

      Matchmarks are not necessary if the back door glass is not going to be reused.

    8. A01NK0A

      Using suction cups, disengage the 2 clips and remove the back door glass.

  19. Click here

    REMOVE BACK DOOR GLASS SPACER


    1. A01NN1B

      Remove the 2 back door glass spacers.

  20. Click here

    REMOVE NO. 2 BACK WINDOW GLASS SPACER


    1. A01NLCR

      Using a scraper, remove the No. 2 back window glass spacer.

      Note:

      • Be careful not to damage the back door glass.

      • Be sure to replace the No. 2 window glass spacer with a new one.

  21. Click here

    REMOVE NO. 1 BACK WINDOW GLASS SPACER

    Tip:

    Use the same procedure for the RH side and LH side.

  22. Click here

    REMOVE BACK WINDOW LOWER MOULDING


    1. A01NL15

      Using a scraper, remove the back window lower moulding.

      Note:

      • Be careful not to damage the windshield glass.

      • Be sure to replace the back window lower moulding with a new one.

  23. Click here

    REMOVE BACK WINDOW OUTSIDE MOULDING


    1. A01NI23

      Using a scraper, remove the back window outside moulding.

      Note:

      • Be careful not to damage the windshield glass.

      • Be sure to replace the back window outside moulding with a new one.

  24. Click here

    CLEAN BACK DOOR GLASS


    1. A01NMYRE02

      Clean the outer edge of the back door glass with a non-residue solvent.

      Note:

      • Do not touch the back door glass surface after cleaning it.

      • Be careful not to damage the glass.

      • Even if using a new back door glass, clean the back door glass with a non-residue solvent.

  25. Click here

    CLEAN VEHICLE BODY


    1. A01NNBPE07

      Using a scraper, remove the moulding and adhesive from the back door glass.

      Table 9. Text in Illustration
      *1 Adhesive
      *2 Body

    2. Clean and shape the contact surfaces of the vehicle body.


      1. Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body, as shown in the illustration.

        Note:

        Be careful not to damage the vehicle body.

        Tip:

        Leave as much adhesive on the vehicle body as possible.

      2. Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.

        Tip:

        Even if all the adhesive has been removed, clean the vehicle body.