FRONT SEAT CUSHION HEATER INSTALLATION


  1. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY


    1. A01NJ58

      Using a tacker, install the front seat cushion heater assembly to the end of the seat cover with 30 new tack pins.

      Note


      • Be careful not to damage the cover.

      • When installing the tack pins, take care to minimize wrinkles as much as possible.

  2. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (w/o Seat Cushion Front Edge Adjustment Function)


    1. A01NNCV

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 19 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    2. A01NKAU

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

  3. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (w/ Seat Cushion Front Edge Adjustment Function)


    1. A01NI86

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 15 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    2. A01NKAU

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

  4. INSTALL FRONT SEAT CUSHION COVER WITH PAD (w/o Seat Cushion Front Edge Adjustment Function)


    1. w/o Climate Control Seat System:


      1. A01NI60

        Engage the 5 clamps.

    2. w/ Climate Control Seat System:


      1. A01NN2L

        Engage the 6 clamps.

      2. Connect the 2 connectors.

    3. for Front Passenger Side:


      1. A01NK6X

        Engage the 2 clamps and connect the occupant detection sensor connector.

    4. Engage each hook as shown in the illustration.

      A01NML4

    5. Install the 2 clips.

    6. A01NK7T

      Engage the 6 hooks and install the front seat cushion cover with pad.

  5. INSTALL FRONT SEAT CUSHION COVER WITH PAD (w/ Seat Cushion Front Edge Adjustment Function)


    1. A01NJ87

      Using hog ring pliers, install 2 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    2. A01NMDO

      Engage the 4 hooks.

    3. Engage each hook as shown in the illustration.

      A01NMFT

    4. for Front Passenger Side:


      1. A01NK6X

        Engage the 2 clamps and connect the occupant detection sensor connector.

    5. Install the 2 clips.

    6. A01NK7T

      Engage the 6 hooks and install the front seat cushion cover with pad.

  6. INSTALL POWER SEAT SWITCH


    1. A01NMNG

      Connect the 2 connectors.

    2. A01NIIB

      Engage the guide.

    3. Install the power seat switch with the 3 screws.

  7. INSTALL FRONT SEAT CUSHION INNER SHIELD


    1. A01NLN7

      Engage the guide and temporarily install the front seat cushion inner shield as shown in the illustration.

    2. A01NI6K

      Engage the claw.

    3. Install the front seat cushion inner shield with the screw.

  8. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY


    1. w/ Seat Cushion Front Edge Adjustment Function:


      1. A01NMZJ

        Connect the connector.

      2. Engage the 2 clamps to the install the seat wire to front seat cushion shield assembly with seat variable cushion switch.

    2. A01NJAX

      Connect the connector to the lumbar switch.

    3. A01NIC5

      Engage the guide and claw.

    4. Install the front seat cushion shield assembly with the 5 screws.

    5. A01NIX4

      Engage the 2 hooks and install the 2 rubber bands of the front seatback board to the seat frame.

  9. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A01NMJR

      Engage the 4 claws and install the slide and vertical power seat switch knob.

  10. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. A01NK6H

      Engage the 4 claws and install the reclining power seat switch knob.

  11. INSTALL FRONT SEAT INNER BELT ASSEMBLY


    1. A01NJV8E01
      Text in Illustration
      *1 Protruding Part

      Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of front seat adjuster.

    2. Connect each connector and clamp.

  12. INSTALL FRONT SEAT ASSEMBLY


    1. Place the front seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. When the power seat slide motor assembly has been removed:


      1. Recline the front seat assembly to the position where the front seat cushion shield assembly screw can be installed.

      2. Install the front seat cushion shield assembly Click here.

      3. Install the slide and vertical power seat switch knob Click here.

      4. Install the reclining power seat switch knob Click here.

    3. Connect each connector under the front seat assembly.

    4. Connect the cable to the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    5. Temporarily install the front seat assembly with the 4 bolts.

    6. Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.

    7. A01NI63E01

      Tighten the 2 bolts on the front side of the front seat assembly.

      Torque:
      37 N*m  { 374 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

    8. Operate the slide and vertical power seat switch knob and move the front seat assembly to the foremost position.

    9. A01NJQ6E01

      Tighten the 2 bolts on the rear side of the front seat assembly.

      Torque:
      37 N*m  { 374 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

  13. INSTALL REAR INNER SEAT TRACK BRACKET COVER


    1. A01NMQK

      Engage the 4 claws and install the rear inner seat track bracket cover as shown in the illustration.

  14. INSTALL REAR OUTER SEAT TRACK BRACKET COVER


    1. A01NLX5

      Engage the 4 claws to install the rear outer seat track bracket cover as shown in the illustration.

  15. INSTALL FRONT INNER SEAT TRACK BRACKET COVER


    1. Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.

    2. A01NL6O

      Engage the 2 guides and 2 claws to install the front inner seat track bracket cover as shown in the illustration.

  16. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER


    1. A01NJWG

      Engage the 2 guides and 2 claws to install the front outer seat track bracket cover as shown in the illustration.

  17. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. A01NN49

      Install the front seat headrest assembly as shown in the illustration.

  18. INSPECT FRONT SEAT ASSEMBLY


    1. Check the power seat operation.

    2. Check the seat heater operation.

      w/o Climate Control Seat System:


      1. Power switch on (IG).

      2. Turn the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.

  19. INSPECT SRS WARNING LIGHT

    Click here

  20. INSTALL REAR DECK FLOOR BOX


    1. A01NIBL

      Install the rear deck floor box with the 3 clips.