REAR SEAT ASSEMBLY (for RH Side) REMOVAL


  1. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.

  2. REMOVE REAR DECK FLOOR BOX


    1. A01NIBL

      Remove the 3 clips and the rear deck floor box.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE REAR SEAT HEADREST ASSEMBLY RH


    1. A01NLXA

      Press the headrest support button and pull up the headrest as shown in the illustration.

  5. REMOVE REAR SEAT CENTER HEADREST ASSEMBLY


    1. A01NI1D

      Press the headrest support button and pull up the headrest as shown in the illustration.

  6. REMOVE REAR SEAT OUTER TRACK BRACKET COVER RH


    1. A01NIHL

      Disengage the 4 claws and remove the rear seat track bracket cover RH.

  7. REMOVE REAR SEAT INNER TRACK BRACKET COVER RH


    1. A01NJAY

      Disengage the 4 claws and remove the 4 rear seat track bracket cover RH.

  8. DISCONNECT REAR SEAT LOCK CABLE ASSEMBLY RH


    1. A01NMNV

      Using a clip remover, remove the 2 clips and disconnect the rear seatback board sub-assembly.

    2. A01NMPV

      Using a clip remover, remove the 3 clips and disconnect the rear seatback board carpet assembly RH.

    3. A01NKPV

      Remove the bolt.

    4. Disengage the guide and disconnect the No. 1 fold seat stopper band assembly.

    5. Pull down the adjusters lock piece to release the lock as shown in the illustration.

      A01NNDYE01
      Text in Illustration
      *1 Adjusters Spring *2 Lock Piece
    6. A01NJMVE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver wrapped with protective tape, disconnect the No. 1 reclining control cable as shown in the illustration.

    7. A01NM5W

      Remove the rear seat reclining control cable from the cover as shown in the illustration.

    8. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

      A01NMOPE01
      Text in Illustration
      *1 Seat Track Adjusting Handle *2 Protective Tape

    9. Using a screwdriver wrapped with protective tape, disconnect the No. 1 rear seat lock cable assembly as shown in the illustration.

    10. Using a screwdriver wrapped with protective tape, disconnect the rear seat lock cable assembly RH as shown in the illustration.

      A01NIZGE01
      Text in Illustration
      *1 Protective Tape

    11. When replacing the rear seat assembly RH or rear seat reclining control cable with a new one:


      1. A01NJ1GE01

        Cut portion A shown in the illustration to separate the rear seat assembly RH or rear seat reclining control cable.

    12. When replacing the rear seat lock cable assembly RH with a new one:


      1. A01NLPYE01

        Cut portion A shown in the illustration to separate the rear seat lock assembly RH.

  9. REMOVE REAR SEAT ASSEMBLY RH


    1. A01NMBJ

      Disconnect the connector.

    2. A01NLN8

      Remove the 3 bolts on the rear side of the seat.

    3. A01NKDM

      Remove the 2 bolts on the front side of the seat and the rear seat assembly RH.

      Note

      Be careful not to damage the vehicle body.