REAR SEAT ASSEMBLY (for LH Side) REMOVAL


  1. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.

  2. REMOVE REAR DECK FLOOR BOX


    1. A01NIBL

      Remove the 3 clips and the rear deck floor box.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE REAR SEAT HEADREST ASSEMBLY LH


    1. A01NM9Q

      Press the headrest support button and pull up the headrest as shown in the illustration.

  5. REMOVE REAR SEAT OUTER TRACK BRACKET COVER LH


    1. A01NI4Q

      Disengage the 4 claws and remove the rear seat outer track bracket cover LH.

  6. REMOVE REAR SEAT INNER TRACK BRACKET COVER LH


    1. A01NML5

      Disengage the 4 claws and remove the rear seat inner track bracket cover LH.

  7. DISCONNECT REAR SEAT LOCK CABLE ASSEMBLY LH


    1. A01NIVW

      Remove the 4 clips.

    2. A01NN7O

      Remove the bolt.

    3. Disengage the guide and disconnect the No. 1 fold seat stopper band assembly.

    4. Pull down the adjuster lock piece to release the lock as shown in the illustration.

      A01NN57E01
      Text in Illustration
      *1 Adjuster Spring *2 Lock Piece
    5. A01NI9VE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver wrapped with protective tape, disconnect the No. 2 reclining control cable as shown in the illustration.

    6. A01NJO6

      Remove the rear seat reclining control cable from the cover as shown in the illustration.

    7. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

      A01NMNFE01
      Text in Illustration
      *1 Seat Track Adjusting Handle *2 Protective Tape

    8. Using a screwdriver wrapped with protective tape, disconnect the No. 2 rear seat reclining control cable as shown in the illustration.

    9. Using a screwdriver wrapped with protective tape, disconnect the rear seat lock cable assembly LH as shown in the illustration.

      A01NM90E01
      Text in Illustration
      *1 Protective Tape

    10. When replacing the rear seat assembly LH or No. 2 rear seat reclining control cable with a new one:


      1. A01NJ1GE01

        Cut portion A shown in the illustration to separate the rear seat assembly LH or No. 2 rear seat reclining control cable.

    11. When replacing the rear seat lock cable assembly LH with a new one:


      1. A01NLPYE01

        Cut portion A shown in the illustration to separate the rear seat lock assembly LH.

  8. REMOVE REAR SEAT ASSEMBLY LH


    1. A01NM11

      Disconnect the connector.

    2. A01NI78

      Remove the 3 bolts on the rear side of the seat.

    3. A01NJPZ

      Remove the 2 bolts on the front side of the seat and the rear seat assembly LH.

      Note

      Be careful not to damage the vehicle body.