FRONT SEAT ASSEMBLY DISASSEMBLY


  1. REMOVE POWER SEAT SLIDE MOTOR ASSEMBLY


    1. Put matchmarks on the seat track rails (upper rail and lower rail).

      A01NJ6XE01
      Text in Illustration
      *a Upper Rail *b Lower Rail
      *c Matchmarks - -
    2. A01NLR6

      Disengage the 2 clamps.

    3. Disconnect the connector.

    4. A01NM37

      While keeping the matchmarks on the seat track rails aligned, remove the 2 nuts by hand.

      Note


      • Make sure that the front seat assembly is in the rearmost position before removing the nuts.

      • If the matchmarks become misaligned, tighten the 2 nuts to the specified torque, place the front seat assembly in the cabin and perform the removal procedure for the power seat slide motor assembly from step (a) again.

      • If a tool is used to remove the nuts, the left and right sides of the seat track rail may become misaligned when removing the sliding motor assembly, resulting in a malfunction of the slide function.

    5. A01NMWP

      Using a 4 mm hexagon wrench, remove the 4 bolts and power seat slide motor assembly as shown in the illustration.

      Note


      • Do not apply excessive force to the slide cable.

      • Do not bend the slide cable more than 60 degrees.

      • Make sure that the washers have not fallen off.

    6. A01NKKQ

      Remove the 2 washers.

  2. REMOVE RECLINING POWER SEAT SWITCH KNOB


    1. A01NIVD

      Using a moulding remover, disengage the 4 claws and remove the reclining power seat switch knob.

  3. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A01NIVN

      Using a moulding remover, disengage the 2 claws as shown in the illustration.

    2. A01NMOV

      Using a moulding remover, disengage the 2 claws and remove the slide and vertical power seat switch knob.

  4. REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY


    1. A01NIX4

      Disengage the 2 hooks and remove the 2 rubber bands of the front seatback board from the front seat frame.

    2. A01NIC5

      Remove the 5 screws.

    3. Disengage the claw and guide.

    4. Disconnect the connector from the front power seat lumbar switch.

    5. w/ Seat Cushion Front Edge Adjustment Function:


      1. A01NMZJ

        Disengage the 2 clamps.

      2. Disconnect the connector from the seat variable cushion switch.

    6. Remove the front seat cushion shield assembly.

  5. REMOVE NO. 1 FRONT SEAT CUSHION INNER SHIELD


    1. A01NJ5B

      Remove the 2 screws.

    2. Disengage the 2 guides and remove the No. 1 front seat cushion inner shield from the front seat cushion shield as shown in the illustration.

  6. REMOVE LUMBAR SWITCH


    1. A01NI4V

      Remove the 2 screws and the lumbar switch.

  7. REMOVE SEAT VARIABLE CUSHION SWITCH (w/ Seat Cushion Front Edge Adjustment Function)


    1. A01NI92

      Remove the 2 screws and the seat variable cushion switch.

  8. REMOVE FRONT SEAT INNER BELT ASSEMBLY


    1. Disconnect each connector and clamp.

    2. A01NK45

      Remove the nut and the front seat inner belt assembly.

  9. REMOVE FRONT SEAT CUSHION INNER SHIELD


    1. A01NI6K

      Remove the screw.

    2. Disengage the claw.

    3. A01NJ52

      Separate the guide and remove the front seat cushion inner shield as shown in the illustration.

  10. REMOVE POWER SEAT SWITCH


    1. A01NIIB

      Remove the 3 screws.

    2. Disengage the guide.

    3. A01NMNG

      Disconnect the 2 connectors and remove the power seat switch.

  11. REMOVE FRONT SEAT CUSHION COVER WITH PAD (w/o Seat Cushion Front Edge Adjustment Function)


    1. A01NK7T

      Disengage the 6 hooks.

    2. w/o Climate Control Seat System:


      1. A01NI60

        Disengage the 5 clamps.

    3. w/ Climate Control Seat System:


      1. A01NN2L

        Disconnect the 2 connectors.

      2. Disengage the 6 clamps.

    4. Using a clip remover, remove the 2 clips.

      A01NLOT

      for Front Passenger Side:


      1. A01NK6X

        Disengage the 2 clamps and separate the occupant detection sensor connector.

    5. Disengage each hook and remove the front seat cushion cover with pad.

  12. REMOVE FRONT SEAT CUSHION COVER WITH PAD (w/ Seat Cushion Front Edge Adjustment Function)


    1. A01NK7T

      Disengage the 6 hooks.

    2. w/o Climate Control Seat System:


      1. A01NI60

        Disengage the 5 clamps.

    3. w/ Climate Control Seat System:


      1. A01NN2L

        Disconnect the 2 connectors.

      2. Disengage the 6 clamps.

    4. Using a clip remover, remove the 2 clips.

      A01NLOT

    5. for Front Passenger Side:


      1. A01NK6X

        Disengage the 2 clamps and separate the occupant detection sensor connector.

    6. Disengage each hook.

    7. A01NMDO

      Disengage the 4 hooks.

    8. A01NJUT

      Remove the 2 hog rings.

    9. Remove the front seat cushion cover with pad.

  13. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER (w/o Seat Cushion Front Edge Adjustment Function)


    1. A01NMWB

      Remove the 2 hog rings.

    2. A01NL60

      Remove the 19 hog rings and the separate type front seat cushion cover from the separate type front seat cushion pad.

  14. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER (w/ Seat Cushion Front Edge Adjustment Function)


    1. A01NMWB

      Remove the 2 hog rings.

    2. A01NIZ7

      Remove the 15 hog rings and the separate type front seat cushion cover from the separate type front seat cushion pad.

  15. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Climate Control Seat System)


    1. A01NJ58

      Cut off the 30 tack pins that fasten the seat heater, and then remove the front seat cushion heater assembly from the separate type front seat cushion cover.

  16. REMOVE TELEVISION BASE COVER CAP (w/ Rear Seat Entertainment System)


    1. A01NL8F

      Using a moulding remover, disengage the 3 claws and 3 guides, and remove the television base cover cap.

  17. REMOVE TELEVISION DISPLAY ASSEMBLY WITH COVER (w/ Rear Seat Entertainment System)


    1. A01NIYI

      Disconnect the connector.

    2. Remove the 3 nuts and television display assembly.

  18. REMOVE NO. 2 TELEVISION BASE (w/ Rear Seat Entertainment System)


    1. A01NJBC

      Remove the 4 screws.

    2. A01NNFW

      Using a clip remover, remove the 5 clips.

    3. Disengage the 2 guides and remove the No. 2 television base.

  19. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY


    1. A01NIVF

      Remove the 2 screws.

    2. A01NMQ2

      Disengage the 2 guides and remove the front seatback board sub-assembly as shown in the illustration.

  20. REMOVE FRONT SEATBACK BOARD COVER SUB-ASSEMBLY


    1. A01NJNH

      Disengage the 2 guides and remove the front seatback board cover sub-assembly.

  21. REMOVE FRONT SEAT HEADREST SUPPORT


    1. A01NKCE

      Disengage the 4 claws and remove the 2 headrest supports.

  22. REMOVE FRONT SEATBACK COVER WITH PAD


    1. A01NIOP

      Disengage the 2 hooks.

    2. A01NJLJ

      Remove the 5 hog rings.

    3. A01NMT2

      Disengage the 6 hooks as shown in the illustration.

    4. A01NJW7

      Remove the nut.

    5. Disengage the guide and remove the seatback cover bracket.

    6. Remove the front seatback cover with pad from the seatback frame.

  23. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    1. A01NN9U

      Remove the 14 hog rings and the separate type front seatback cover from the separate type front seatback pad.

  24. REMOVE FRONT SEATBACK HEATER ASSEMBLY (w/ Climate Control Seat System)


    1. A01NKJW

      Cut off the 12 tack pins that fasten the seatback heater, and then remove the front seatback heater assembly from the separate type front seat cushion cover.

  25. REMOVE SEATBACK CLIMATE CONTROL BLOWER (w/ Climate Control Seat System)


    1. for Driver Side:


      1. A01NM0T

        Disconnect the connector.

      2. Disengage the 3 clamps.

    2. for Front Passenger Side:


      1. A01NKMT

        Disconnect the connector.

      2. Disengage the clamp.

    3. A01NM2N

      Disengage the clamp.

    4. Using a T30 ''TORX'' socket, remove the 6 ''TORX'' bolts and remove the seatback climate control blower and the seatback climate control cover.

  26. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY


    1. A01NM16

      Disengage the 4 guides and remove the seatback felt.

    2. A01NMZE

      Disengage the 4 clamps.

    3. A01NLF0

      Disengage the 2 guides and remove the front seatback spring sub-assembly as shown in the illustration.

    4. A01NKWJ

      Disconnect the connector.

    5. Remove the 2 screws.

    6. Disengage the guide and remove the lumbar support adjuster assembly.

    7. A01NJ2I

      Remove the bush.

  27. REMOVE ACTIVE HEADREST UPPER UNIT


    1. A01NMSSE01

      Remove the nut <A> and disconnect the cable from the active headrest upper unit as shown in the illustration.

    2. Remove the 4 nuts <B> and the active headrest upper unit.

  28. REMOVE ACTIVE HEADREST LOWER UNIT


    1. A01NJIH

      Remove the 2 nuts and the active headrest lower unit.

  29. REMOVE LOWER RECLINING ADJUSTER INSIDE COVER LH


    1. A01NKTOE01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Remove the 2 screws.

    2. Disengage the clamp and remove the side airbag wire harness.

    3. Disengage the guide and remove the lower reclining adjuster inside cover LH.

  30. REMOVE UPPER RECLINING ADJUSTER INSIDE COVER LH


    1. A01NMTB

      Remove the screw.

    2. Disengage the guide and remove the upper reclining adjuster inside cover LH.

  31. REMOVE LOWER RECLINING ADJUSTER INSIDE COVER RH


    1. A01NKKFE01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Remove the 2 screws.

    2. Disengage the clamp and remove the side airbag wire harness.

    3. Disengage the guide and remove the lower reclining adjuster inside cover RH.

  32. REMOVE UPPER RECLINING ADJUSTER INSIDE COVER RH


    1. A01NL1U

      Remove the screw.

    2. Disengage the guide and remove the upper reclining adjuster inside cover RH.

  33. REMOVE FRONT SEAT LOWER CUSHION SHIELD LH


    1. A01NMQVE01
      Text in Illustration
      *1 Hook
      *2 Guide

      Remove the screw.

    2. Disengage the hook as shown in the illustration.

    3. Disengage the guide and remove the front seat lower cushion shield LH.

  34. REMOVE FRONT SEAT LOWER CUSHION SHIELD RH


    1. A01NI3HE01
      Text in Illustration
      *1 Hook
      *2 Guide

      Remove the screw.

    2. Disengage the hook as shown in the illustration.

    3. Disengage the guide and remove the front seat lower cushion shield RH.

  35. REMOVE SEAT CUSHION CLIMATE CONTROL DUCT (w/ Climate Control Seat System)


    1. A01NIQBE01

      Disengage the 2 clamps (A) in the direction indicated by the arrow.

    2. Disengage the 2 clamps (B) in the direction indicated by the arrow.

    3. Disengage the 2 claws, and remove the seat cushion climate control duct.

  36. REMOVE SEAT CUSHION CLIMATE CONTROL BLOWER (w/ Climate Control Seat System)


    1. A01NIT6

      Disconnect the connector.

    2. Remove the screw.

    3. Pull up the bracket of the seat cushion climate control blower as shown in the illustration.

    4. Disengage the 2 hooks and remove the seat cushion climate control blower.

  37. REMOVE SEAT POSITION SENSOR


    1. A01NMZN

      Disconnect the connector.

    2. Using a T30 "TORX" socket wrench, remove the "TORX" screw and seat position sensor with the seat slide position sensor protector.

    3. A01NLPG

      Remove the seat position sensor from the seat slide position sensor protector as shown in the illustration.

  38. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Climate Control Seat System)


    1. A01NL1B

      Disconnect the connector.

    2. Disengage the 2 guides and remove the seat heater control sub-assembly.

  39. REMOVE FRONT SEAT WIRE


    1. w/ Rear Seat Entertainment System:


      1. A01NL0U

        Disengage the 5 clamps.

    2. A01NJLW

      Disconnect the connector.

    3. Disengage the 3 clamps.

    4. A01NI50

      Disconnect the 3 connectors.

    5. Disengage the 8 clamps and remove the front seat wire from the front seat frame assembly with adjuster.

  40. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY


    1. A01NJGR

      Disengage the 3 clamps to separate the wire harness.

    2. A01NKNT

      Disengage the 2 clamps.

    3. A01NNFS

      Remove the 2 nuts and front seat side airbag assembly.

      CAUTION:


      • The nuts must not be reused.

      • Make sure that the front seat frame assembly with adjuster is not deformed. If it is, replace it with a new one.