Click here

KNEE AIRBAG ASSEMBLY (for Front Passenger Side) INSTALLATION

Click here
Click here Click here
  1. Click here

    INSTALL FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01NJOC

      Connect the airbag connector to the front passenger side knee airbag assembly.

      Note:

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. A01NN2H

      Temporarily install the front passenger side knee airbag assembly with the claw and 2 pins.

    5. Install the front passenger side knee airbag assembly with the 3 bolts.

      10 N*m 102 kgf*cm 7 ft.*lbf
      Note:

      Confirm that the front passenger side knee airbag assembly is installed securely without any excessive gaps and is not protruding outward.

    6. A01NIOQE01

      Remove the protective tape.

      Table 1. Text in Illustration
      *1 Protective Tape
  2. Click here

    INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Connect the connector.

    2. A01NLUH

      Engage the 2 guides and 4 claw to install the No. 2 instrument panel under cover sub-assembly.

  3. Click here

    INSTALL LOWER INSTRUMENT PANEL FINISH PANEL


    1. A01NMLC

      Engage the 7 clips to install the lower instrument panel finish panel as shown in the illustration.

  4. Click here

    INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. Engage the clamp.

    2. Connect each connector.

    3. A01NINT

      Engage the 3 claws and 3 clips.

    4. w/o Seat Heater System:


      1. Connect the connector to the console box hole cover.

    5. w/ Seat Heater System:


      1. Connect the connector.

      2. Engage the 6 claws to install the seat heater switch with console box hole cover.

    6. A01NJIY

      Engage the 4 claws and 4 clips to install the upper console panel sub-assembly.

  5. Click here

    INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A01NIFY

      Turn the shift lever knob sub-assembly clockwise to install the shift lever knob sub-assembly.

  6. Click here

    INSTALL INSTRUMENT PANEL GARNISH RH (w/o Airbag Cut Off Switch)

    Tip:

    Use the same procedure for the RH side and LH side (Click here).

  7. Click here

    INSTALL INSTRUMENT PANEL GARNISH RH (w/ Airbag Cut Off Switch)


    1. Connect the connector.

    2. A01NM3A

      Engage the 6 clips to install the instrument panel garnish RH.

  8. Click here

    INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

    Tip:

    Use the same procedure for the RH side and LH side (Click here).

  9. Click here

    INSTALL FRONT DOOR SCUFF PLATE RH

    Tip:

    Use the same procedure for the RH side and LH side (Click here).

  10. Click here

    CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  11. Click here

    INSTALL REAR DECK FLOOR BOX


    1. A01NIBL

      Install the rear deck floor box with the 3 clips.

  12. Click here

    PERFORM DIAGNOSTIC SYSTEM CHECK


    1. Perform a diagnostic system check (Click here).

  13. Click here

    INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light (Click here).