SPIRAL CABLE REMOVAL


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  3. REMOVE REAR DECK FLOOR BOX


    1. A01NIBL

      Remove the 3 clips and the rear deck floor box.

  4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


    1. Disable the auto away/return function by changing the customize parameter Click here.

      Note

      Record the current customize parameter setting (whether the auto away/return function is enabled or disabled) in order to restore the current setting after finishing this operation.

      Tech Tips

      Performing the above operation disables the auto away/return function when the power switch is turned off.

    2. Turn the power switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.

    3. Turn the power switch off and disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. REMOVE LOWER NO. 3 STEERING WHEEL COVER


    1. A01NMZR

      Disengage the claw to remove the lower No. 3 steering wheel cover.

  6. REMOVE LOWER NO. 2 STEERING WHEEL COVER


    1. A01NJTR

      Disengage the claw to remove the lower No. 2 steering wheel cover.

  7. REMOVE STEERING PAD

    CAUTION:

    When storing the steering pad, keep the airbag deployment side facing upward.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A01NMYA

      Using a screwdriver, push the 3 torsion springs to detach the 3 pins as shown in the illustration.

      Note

      Do not drop the steering pad.

      Tech Tips

      Insert the screwdriver from the installation holes in the lower No. 3 steering wheel cover and lower No. 2 steering wheel cover.

    4. A01NIWN

      Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand.

      Note

      When removing the steering pad, do not pull the airbag wire harness.

    5. Using a screwdriver with its tip wrapped with protective tape, release the 2 airbag connector locks.

    6. Using a screwdriver with its tip wrapped with protective tape, disconnect the 2 airbag connectors.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

    7. Disconnect the horn connector to remove the steering pad.

  8. REMOVE STEERING WHEEL ASSEMBLY


    1. Disconnect each connector from the spiral cable.

    2. w/ Steering Heater:


      1. A01NNFP

        Disconnect the connector.

    3. A01NIURE01
      Text in Illustration
      *a Matchmark

      Remove the steering wheel assembly set nut.

    4. Put matchmarks on the steering wheel assembly and steering main shaft.

    5. A01NJZZE01
      Text in Illustration
      *a Turn
      *b Hold

      Using SST, remove the steering wheel assembly.

      SST
      09950-50013   ( 09951-05010, 09952-05010, 09953-05020, 09954-05070 )

      Note

      Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.

  9. REMOVE STEERING COLUMN COVER

    Note

    Removing the lower steering column cover in the incorrect order will cause the parts to break.


    1. A01NKVRE01
      Text in Illustration
      *1 Instrument Panel Cluster Finish Panel

      Disengage the 4 clips and 2 guides to separate the instrument panel cluster finish panel from the upper steering column cover.

    2. A01NMV8

      Remove the 3 screws.

    3. Disengage the 2 claws to remove the lower steering column cover.

      Note

      Do not damage the tilt and telescopic switch.

    4. A01NKMK

      Disengage the claw to remove the upper steering column cover.

  10. REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note


    • Do not replace the spiral cable with the auxiliary battery connected and the power switch on (IG).

    • Do not rotate the spiral cable with the auxiliary battery connected and the power switch on (IG).

    • Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.

    • Do not remove the steering sensor from the spiral cable.


    1. A01NIOGE01
      Text in Illustration
      *1 Slider

      Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable with sensor sub-assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

    2. Disconnect the other connector from the spiral cable with sensor sub-assembly.

    3. A01NJEM

      Disengage the 3 claws and remove the spiral cable with sensor sub-assembly.