Click here

AIRBAG SYSTEM, Diagnostic DTC:B1627/82, B1628/82, B1637/82, B1638/82, B1647/82

Click here
Click here Click here
DTC Code DTC Name
B1627/82 Lost communication with Side Airbag Sensor LH
B1628/82 Side Airbag Sensor Assembly LH Initialization Incomplete
B1637/82 Lost Communication with Rear Airbag Sensor LH
B1638/82 Rear Airbag Sensor Assembly LH Initialization Incomplete
B1647/82 Lost Communication with Side Satellite Sensor Bus LH
Click here

DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH) is composed of the center airbag sensor assembly, side airbag sensor LH, and rear airbag sensor LH.

The side airbag sensor LH and rear airbag sensor LH detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbag should be deployed.

These DTCs are recorded when a malfunction is detected for the side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).

DTC No. DTC Detection Condition Trouble Area

B1627/82

B1628/82

B1637/82

B1638/82

B1647/82

  • The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).

  • Side airbag sensor LH malfunction

  • Rear airbag sensor LH malfunction

  • Center airbag sensor assembly malfunction

  • No. 2 floor wire

  • Side airbag sensor LH

  • Rear airbag sensor LH

  • Center airbag sensor assembly
Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Click here

PROCEDURE


  1. Click here

    CHECK PRESENT DTC


    1. Turn the power switch on (IG), and wait for at least 60 seconds.

    2. Check for present DTCs (Click here).

      Result
      Result Proceed to
      Present DTC B1647 or 82 is output. A
      Present DTC B1628 is output. B
      Present DTC B1637 or B1638 is output. C
      Present DTC B1627 is output. D
      Present DTCs B1627, B1628, B1637, B1638, B1647 and 82 are not output. E
      Tip:

      • DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the power switch off and then on (IG) again.

      • Codes other than DTCs B1627, B1628, B1637, B1638, B1647 and 82 may be output at this time, but they are not related to this check.


  2. Click here

    CHECK CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      Note:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the center airbag sensor assembly, side airbag sensor LH and rear airbag sensor LH.

      OK
      The connectors are properly connected.
      Tip:

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the center airbag sensor assembly, side airbag sensor LH and rear airbag sensor LH.

    5. Check that the terminals of connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

  3. Click here

    CHECK NO. 2 FLOOR WIRE (OPEN)


    1. A01NK5IE02

      Using SST, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

      Table 1. Text in Illustration
      *1 Side Airbag Sensor LH *2 Center Airbag Sensor Assembly
      *3 No. 2 Floor Wire *4

      Front view of wire harness connector

      (to Center Airbag Sensor Assembly)
      *5

      Front view of wire harness connector

      (to Side Airbag Sensor LH)

      		 *6 Connector B
      *7 Connector C - -
      Note:

      Do not forcibly insert SST into the terminals of the connector when connecting.

      09843-18040

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-4 (BBL+) - P4-3 (BBL-) Always Below 1 Ω

    3. Disconnect SST from connector B.


  4. Click here

    CHECK NO. 2 FLOOR WIRE (SHORT)


    1. A01NI85E03

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-4 (BBL+) - P4-3 (BBL-) Always 1 MΩ or higher
      Table 2. Text in Illustration
      *1 Side Airbag Sensor LH
      *2 Center Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector C

  5. Click here

    CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. A01NI85E03

      Connect the cable to the negative (-) battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      P4-4 (BBL+) - Body ground Power switch on (IG) Below 1 V
      P4-3 (BBL-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      Note:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Table 3. Text in Illustration
      *1 Side Airbag Sensor LH
      *2 Center Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector C

  6. Click here

    CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. A01NI85E03

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-4 (BBL+) - Body ground Always 1 MΩ or higher
      P4-3 (BBL-) - Body ground Always 1 MΩ or higher
      Table 4. Text in Illustration
      *1 Side Airbag Sensor LH
      *2 Center Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector C

  7. Click here

    CHECK NO. 2 FLOOR WIRE (OPEN)


    1. A01NIW3E07

      Using SST, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

      Table 5. Text in Illustration
      *1 Rear Airbag Sensor LH *2 Side Airbag Sensor LH
      *3 No. 2 Floor Wire *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      		 *6 Connector B
      *7 Connector C - -
      Note:

      Do not forcibly insert SST into the terminals of the connector when connecting.

      09843-18040

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-1 (BCL+) - P4-2 (BCL-) Always Below 1 Ω

    3. Disconnect SST from connector C.


  8. Click here

    CHECK NO. 2 FLOOR WIRE (SHORT)


    1. A01NI56E04

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-1 (BCL+) - P4-2 (BCL-) Always 1 MΩ or higher
      Table 6. Text in Illustration
      *1 Rear Airbag Sensor LH
      *2 Side Airbag Sensor LH
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector B

  9. Click here

    CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. A01NI56E04

      Connect the cable to the negative (-) battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      P4-1 (BCL+) - Body ground Power switch on (IG) Below 1 V
      P4-2 (BCL-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      Note:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Table 7. Text in Illustration
      *1 Rear Airbag Sensor LH
      *2 Side Airbag Sensor LH
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector B

  10. Click here

    CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. A01NI56E04

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-1 (BCL+) - Body ground Always 1 MΩ or higher
      P4-2 (BCL-) - Body ground Always 1 MΩ or higher
      Table 8. Text in Illustration
      *1 Rear Airbag Sensor LH
      *2 Side Airbag Sensor LH
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector B

  11. Click here

    CHECK SIDE AIRBAG SENSOR LH


    1. A01NLHOE01

      Connect the connectors to the rear airbag sensor LH and center airbag sensor assembly.

    2. Interchange the side airbag sensor LH with RH and connect the connectors.

    3. Connect the cable to the negative (-) battery terminal.

    4. Turn the power switch on (IG), and wait for at least 60 seconds.

    5. Clear the DTCs stored in the memory (Click here).

    6. Turn the power switch off.

    7. Turn the power switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs (Click here).

      Result
      Result Proceed to
      DTC B1647 or 82 is output. A
      DTC B1642 or 81 is output. B
      DTCs B1642, B1647, 81 and 82 are not output. C
      Tip:

      Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) battery terminal.

      Note:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    11. Return the side airbag sensor LH and RH to their original positions and connect the connectors.

      Table 9. Text in Illustration
      *1 Side Airbag Sensor RH
      *2 Center Airbag Sensor Assembly

  12. Click here

    CHECK REAR AIRBAG SENSOR LH


    1. A01NJC4E16

      Interchange the rear airbag sensor LH with RH and connect the connectors.

    2. Connect the cable to the negative (-) battery terminal.

    3. Turn the power switch on (IG), and wait for at least 60 seconds.

    4. Clear the DTCs stored in the memory (Click here).

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs (Click here).

      Result
      Result Proceed to
      DTCs B1642, B1647, 81 and 82 are not output. A
      DTC B1647 or 82 is output. B
      DTC B1642 or 81 is output. C
      Tip:

      Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) battery terminal.

      Note:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    10. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.

      Table 10. Text in Illustration
      *1 Rear Airbag Sensor RH
      *2 Side Airbag Sensor LH

  13. Click here

    CHECK PAST DTC


    1. Turn the power switch on (IG), and wait for at least 60 seconds.

    2. Check for past DTCs (Click here).

      Result
      Result Proceed to
      Past DTC B1627 is not output. A
      Past DTC B1627 is output. B
      Tip:

      Codes other than past DTC B1627 may be output at this time, but they are not related to this check.


  14. Click here

    CHECK CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      Note:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the center airbag sensor assembly and side airbag sensor LH.

      OK
      The connectors are properly connected.
      Tip:

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the center airbag sensor assembly and side airbag sensor LH.

    5. Check that the terminals of connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

  15. Click here

    CHECK NO. 2 FLOOR WIRE (OPEN)


    1. A01NK5IE02

      Using SST, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

      Table 11. Text in Illustration
      *1 Side Airbag Sensor LH *2 Center Airbag Sensor Assembly
      *3 No. 2 Floor Wire *4

      Front view of wire harness connector

      (to Center Airbag Sensor Assembly)
      *5

      Front view of wire harness connector

      (to Side Airbag Sensor LH)

      		 *6 Connector B
      *7 Connector C - -
      Note:

      Do not forcibly insert SST into the terminals of the connector when connecting.

      09843-18040

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-4 (BBL+) - P4-3 (BBL-) Always Below 1 Ω

    3. Disconnect SST from connector B.


  16. Click here

    CHECK NO. 2 FLOOR WIRE (SHORT)


    1. A01NI85E03

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-4 (BBL+) - P4-3 (BBL-) Always 1 MΩ or higher
      Table 12. Text in Illustration
      *1 Side Airbag Sensor LH
      *2 Center Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector C

  17. Click here

    CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. A01NI85E03

      Connect the cable to the negative (-) battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      P4-4 (BBL+) - Body ground Power switch on (IG) Below 1 V
      P4-3 (BBL-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      Note:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Table 13. Text in Illustration
      *1 Side Airbag Sensor LH
      *2 Center Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector C

  18. Click here

    CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. A01NI85E03

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-4 (BBL+) - Body ground Always 1 MΩ or higher
      P4-3 (BBL-) - Body ground Always 1 MΩ or higher
      Table 14. Text in Illustration
      *1 Side Airbag Sensor LH
      *2 Center Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector C

  19. Click here

    CHECK SIDE AIRBAG SENSOR LH


    1. A01NLHOE01

      Connect the connector to the center airbag sensor assembly.

    2. Interchange the side airbag sensor LH with RH and connect the connectors.

    3. Connect the cable to the negative (-) battery terminal.

    4. Turn the power switch on (IG), and wait for at least 60 seconds.

    5. Clear the DTCs stored in the memory (Click here).

    6. Turn the power switch off.

    7. Turn the power switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs (Click here).

      Result
      Result Proceed to
      DTCs B1623 and B1628 are not output. A
      DTC B1628 is output. B
      DTC B1623 is output. C
      Tip:

      Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) battery terminal.

      Note:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    11. Return the side airbag sensor LH and RH to their original positions and connect the connectors.

      Table 15. Text in Illustration
      *1 Side Airbag Sensor RH
      *2 Center Airbag Sensor Assembly

  20. Click here

    CHECK CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      Note:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the side airbag sensor LH and rear airbag sensor LH.

      OK
      The connectors are properly connected.
      Tip:

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.

    5. Check that the terminals of connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

  21. Click here

    CHECK NO. 2 FLOOR WIRE (OPEN)


    1. A01NIW3E07

      Using SST, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

      Table 16. Text in Illustration
      *1 Rear Airbag Sensor LH *2 Side Airbag Sensor LH
      *3 No. 2 Floor Wire *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      		 *6 Connector B
      *7 Connector C - -
      Note:

      Do not forcibly insert SST into the terminals of the connector when connecting.

      09843-18040

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-1 (BCL+) - P4-2 (BCL-) Always Below 1 Ω

    3. Disconnect SST from connector C.


  22. Click here

    CHECK NO. 2 FLOOR WIRE (SHORT)


    1. A01NI56E04

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-1 (BCL+) - P4-2 (BCL-) Always 1 MΩ or higher
      Table 17. Text in Illustration
      *1 Rear Airbag Sensor LH
      *2 Side Airbag Sensor LH
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector B

  23. Click here

    CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. A01NI56E04

      Connect the cable to the negative (-) battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      P4-1 (BCL+) - Body ground Power switch on (IG) Below 1 V
      P4-2 (BCL-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      Note:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Table 18. Text in Illustration
      *1 Rear Airbag Sensor LH
      *2 Side Airbag Sensor LH
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector B

  24. Click here

    CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. A01NI56E04

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-1 (BCL+) - Body ground Always 1 MΩ or higher
      P4-2 (BCL-) - Body ground Always 1 MΩ or higher
      Table 19. Text in Illustration
      *1 Rear Airbag Sensor LH
      *2 Side Airbag Sensor LH
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector B

  25. Click here

    CHECK SIDE AIRBAG SENSOR LH


    1. A01NLHOE01

      Connect the connector to the rear airbag sensor LH.

    2. Interchange the side airbag sensor LH with RH and connect the connectors.

    3. Connect the cable to the negative (-) battery terminal.

    4. Turn the power switch on (IG), and wait for at least 60 seconds.

    5. Clear the DTCs stored in the memory (Click here).

    6. Turn the power switch off.

    7. Turn the power switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs (Click here).

      Result
      Result Proceed to
      DTC B1637 or B1638 is output. A
      DTC B1632 or B1633 is output. B
      DTCs B1632, B1633, B1637 and B1638 are not output. C
      Tip:

      Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) battery terminal.

      Note:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    11. Return the side airbag sensor LH and RH to their original positions and connect the connectors.

      Table 20. Text in Illustration
      *1 Side Airbag Sensor RH
      *2 Center Airbag Sensor Assembly

  26. Click here

    CHECK REAR AIRBAG SENSOR LH


    1. A01NJC4E16

      Interchange the rear airbag sensor LH with RH and connect the connectors.

    2. Connect the cable to the negative (-) battery terminal.

    3. Turn the power switch on (IG), and wait for at least 60 seconds.

    4. Clear the DTCs stored in the memory (Click here).

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs (Click here).

      Result
      Result Proceed to
      DTCs B1632, B1633, B1637 and B1638 are not output. A
      DTC B1637 or B1638 is output. B
      DTC B1632 or B1633 is output. C
      Tip:

      Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) battery terminal.

      Note:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    10. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.

      Table 21. Text in Illustration
      *1 Rear Airbag Sensor RH
      *2 Side Airbag Sensor LH

  27. Click here

    CHECK SIDE AIRBAG SENSOR LH


    1. A01NLHOE01

      Turn the power switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      Note:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Interchange the side airbag sensor LH with RH and connect the connectors.

    4. Connect the cable to the negative (-) battery terminal.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Clear the DTCs stored in the memory (Click here).

    7. Turn the power switch off.

    8. Turn the power switch on (IG), and wait for at least 60 seconds.

    9. Check for DTCs (Click here).

      Result
      Result Proceed to
      DTCs B1622 and B1627 are not output. A
      DTC B1627 is output. B
      DTC B1622 is output. C
      Tip:

      Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.

    10. Turn the power switch off.

    11. Disconnect the cable from the negative (-) battery terminal.

      Note:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    12. Return the side airbag sensor LH and RH to their original positions and connect the connectors.

      Table 22. Text in Illustration
      *1 Side Airbag Sensor RH
      *2 Center Airbag Sensor Assembly

  28. Click here

    USE SIMULATION METHOD TO CHECKClick here

  29. Click here

    REPLACE NO. 2 FLOOR WIRE

  30. Click here

    REPLACE SIDE AIRBAG SENSOR LHClick here

  31. Click here

    REPLACE REAR AIRBAG SENSOR LHClick here

  32. Click here

    REPLACE CENTER AIRBAG SENSOR ASSEMBLYClick here