ELECTRICAL KEY OSCILLATOR (for Front Floor) REMOVAL


  1. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.

  2. REMOVE REAR DECK FLOOR BOX (w/ Air Suspension)


    1. A01NIBL

      Remove the 3 clips and the rear deck floor box.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Air Suspension)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE REAR CONSOLE BOX ASSEMBLY

    Click here

  5. REMOVE INSTRUMENT PANEL GARNISH LH


    1. A01NJH3

      Using moulding remover B, disengage the 6 clips and remove the instrument panel garnish LH as shown in the illustration.

  6. REMOVE NO. 1 SWITCH HOLE BASE


    1. A01NJL9

      Push the No. 1 switch hole base in the direction indicated by the arrow to disengage the 4 claws and 2 guides.

    2. Disconnect each connector and remove the No. 1 switch hole base.

  7. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A01NL83

      Disengage the 2 claws and open the cover as shown in the illustration.

    2. A01NLP9

      Remove the 2 screws <D>.

    3. Disengage the 8 clips and 2 guides.

    4. Disconnect each connector and remove the lower instrument panel finish panel sub-assembly.

  8. REMOVE INSTRUMENT PANEL FINISH PANEL


    1. A01NKT2

      Pull the instrument panel finish panel in the direction indicated by the arrow to disengage the claw, 2 clips and 2 guides, and remove the instrument panel finish panel.

  9. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL


    1. A01NJY6

      Pull the lower instrument panel finish panel in the direction indicated by the arrow to disengage the 7 clips and remove the lower instrument panel finish panel.

  10. REMOVE FRONT CONSOLE BOX COVER


    1. A01NJ78

      Using moulding remover A, disengage the 2 clips and 5 guides.

    2. Disconnect the connector and remove the front console box cover.

  11. REMOVE CONSOLE BOX (for LHD)


    1. A01NK2D

      Remove the 5 screws <D>.

    2. A01NM94E01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Disengage the 2 clamps.

    3. Remove the 3 clips.

    4. Disengage the 3 guides and remove the console box as shown in the illustration.

  12. REMOVE CONSOLE BOX (for RHD)


    1. A01NJHE

      Remove the 5 screws <D>.

    2. A01NN20E01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Disengage the 2 clamps.

    3. Remove the 2 clips.

    4. Disengage the 3 guides and remove the console box as shown in the illustration.

  13. REMOVE ELECTRICAL KEY OSCILLATOR


    1. A01NMZ8

      Disconnect the connector.

    2. Disengage the clamp and remove the electrical key oscillator.

      Note

      Be careful when removing the electrical key oscillator. If the oscillator is dropped, replace it with a new one.