Click here

CAN COMMUNICATION SYSTEM, Diagnostic DTC:U0182

Click here
Click here Click here
DTC Code DTC Name
U0182 Lost Communication with AFS ECU
Click here

DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
U0182 No communication from the AFS ECU continues.

  • AFS ECU branch wire or connector

  • Power source circuit of AFS ECU

  • AFS ECU
A01NMRBE03
Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Note:

  • Turn the power switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.

  • Turn the power switch off before inspecting CAN bus wires for a ground short.

  • After the power switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.

  • Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the power switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

Tip:

  • Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

Click here

PROCEDURE


  1. Click here

    RECONFIRM DTC OUTPUT


    1. Reconfirm DTCs.

      Tip:

      If CAN No. 2 bus DTC U1002 is output from the power management control ECU (Intelligent tester display/PM1 Gateway), troubleshoot for U1002 and check for malfunctions in the CAN No. 2 main bus circuit.

      Result
      Result Proceed to
      U1002 is not output from power management control ECU (Intelligent tester display/PM1 Gateway) A
      U1002 is output from power management control ECU (Intelligent tester display/PM1 Gateway) B

  2. Click here

    CHECK CAN BUS WIRE FOR DISCONNECTION (AFS ECU BRANCH WIRE)


    1. Turn the power switch off.

    2. A01NKN8E10

      Disconnect the AFS ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Value
      A53-12 (CANH) - A53-13 (CANL) Power switch off 54 to 69 Ω
      Table 1. Text in Illustration
      *1

      Front view of wire harness connector

      (to AFS ECU)

  3. Click here

    CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    1. Turn the power switch on (IG).

    2. A01NKN8E11

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      A53-15 (IG) - Body ground Power switch on (IG) 11 to 14 V
      Table 2. Text in Illustration
      *1

      Front view of wire harness connector

      (to AFS ECU)

  4. Click here

    CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)


    1. Turn the power switch off.

    2. A01NKN8E15

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A53-22 (E1) - Body ground Always Below 1 Ω
      Table 3. Text in Illustration
      *1

      Front view of wire harness connector

      (to AFS ECU)

  5. Click here

    REPLACE AFS ECUClick here

  6. Click here

    GO TO CIRCUITS INDICATED BY OUTPUT DTCSClick here

  7. Click here

    REPAIR OR REPLACE CAN BUS BRANCH WIRE (AFS ECU BRANCH WIRE)

  8. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

  9. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND TERMINAL)