Click here

PARKING ASSIST ECU REMOVAL

Click here
Click here Click here
  1. Click here

    PRECAUTION

    Note:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work (Click here).

  2. Click here

    REMOVE REAR DECK FLOOR BOX


    1. A01NIBL

      Remove the 3 clips and the rear deck floor box.

  3. Click here

    DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the auxiliary battery negative (-) terminal to disable the SRS system.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  4. Click here

    REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A01NMB2

      Turn the shift lever knob sub-assembly counterclockwise and remove the shift lever knob sub-assembly.

  5. Click here

    REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A01NIU0

      Move the shift lever to N.

    2. Pull the upper console panel sub-assembly in the direction indicated by the arrow to disengage the 4 claws and 4 clips.

    3. w/o Seat Heater System:


      1. Disconnect the connector from the console box hole cover.

    4. A01NJCF

      w/ Seat Heater System:


      1. Disengage the 6 claws.

      2. Disconnect the connector and remove the seat heater switch with console box hole cover.

    5. A01NN09

      Pull the upper console panel sub-assembly in the direction indicated by the arrow to disengage the 3 claws and 3 clips.

    6. Disconnect each connector.

    7. Disengage the clamp and remove the upper console panel sub-assembly.

  6. Click here

    REMOVE LOWER INSTRUMENT PANEL FINISH PANEL


    1. A01NJY6

      Pull the lower instrument panel finish panel in the direction indicated by the arrow to disengage the 7 clips and remove the lower instrument panel finish panel.

  7. Click here

    REMOVE FRONT DOOR SCUFF PLATE RH

    Tip:

    Use the same procedure for the RH side and LH side (Click here).

  8. Click here

    REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tip:

    Use the same procedure for the RH side and LH side (Click here).

  9. Click here

    REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A01NI4T

      Disengage the 4 claws and 2 guides as shown in the illustration.

    2. Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.

  10. Click here

    REMOVE INSTRUMENT PANEL GARNISH RH (w/o Airbag Cut Off Switch)

    Tip:

    Use the same procedure for the RH side and LH side (Click here).

  11. Click here

    REMOVE INSTRUMENT PANEL GARNISH RH (w/ Airbag Cut Off Switch)


    1. A01NJRN

      Using moulding remover B, disengage the 6 clips as shown in the illustration.

    2. Disconnect the connector and remove the instrument panel garnish RH.

  12. Click here

    REMOVE FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY

    CAUTION:

    When storing the front passenger side knee airbag assembly, keep the airbag deployment side facing upward.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01NIOQE01

      Put protective tape around the front passenger side knee airbag assembly.

      Table 1. Text in Illustration
      *1 Protective Tape
    4. A01NN2H

      Remove the 3 bolts.

    5. Disengage the claw and 2 pins to separate the front passenger side knee airbag assembly.

    6. A01NMVSE01

      Using a screwdriver with the tip wrapped with protective tape, disconnect the airbag connector to remove the front passenger side knee airbag assembly.

      Table 2. Text in Illustration
      *1 Protective Tape
      Note:

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  13. Click here

    REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    1. A01NJ44

      Remove the 5 screws <F>.

    2. A01NJQM

      Disengage the claw, 4 clips and guide.

    3. Disconnect each connector and remove the glove compartment door assembly.

  14. Click here

    DISCONNECT CONNECTOR HOLDER (for LHD)


    1. A01NJGZ

      Disengage the clamp and disconnect the wire harness.

    2. Remove the nut.

    3. Disengage the claw and disconnect the connector holder.

  15. Click here

    REMOVE ECU INTEGRATION BOX


    1. A01NJ9O

      Remove the bolt, 2 nuts and ECU integration box.

  16. Click here

    REMOVE PARKING ASSIST ECU


    1. A01NJJP

      Disengage the 2 claws and remove the parking assist ECU as shown in the illustration.