STEERING ANGLE SENSOR INSTALLATION


  1. INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY


    1. Install the spiral cable with sensor sub-assembly Click here.

      Note


      • Do not replace the spiral cable with sensor sub-assembly with the battery connected and the power switch on (IG).

      • Do not rotate the spiral cable with sensor sub-assembly with the battery connected and the power switch on (IG).

      • Ensure that the steering wheel is installed and aligned straight when inspecting the steering angle sensor.

      • Do not remove the steering angle sensor from the spiral cable.

  2. INSTALL STEERING COLUMN COVER


    1. A01NKMK

      Engage the claw to install the upper steering column cover.

    2. A01NMV8

      Engage the 2 claws to install the lower steering column cover to the upper steering column cover.

      Note

      Do not damage the tilt and telescopic switch.

    3. Install the 3 screws.

      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }
    4. A01NKVRE01
      Text in Illustration
      *1 Instrument Panel Cluster Finish Panel

      Engage the 4 clips and 2 guides to install the instrument panel cluster finish panel to the upper steering column cover.

  3. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

  4. ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01NKO6

      Rotate the spiral cable counterclockwise slowly by hand until it stops.

      Note

      Do not turn the spiral cable using the airbag wire harness.

    4. A01NIE2E01
      Text in Illustration
      *A w/o Steering Heater
      *B w/ Steering Heater
      *C Type A
      *D Type B
      *a Alignment Mark

      Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

      Note

      Do not turn the spiral cable using the airbag wire harness.

      Tech Tips

      The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.

  5. INSTALL STEERING WHEEL ASSEMBLY


    1. A01NIURE01
      Text in Illustration
      *a Matchmark

      Install the steering wheel assembly aligning the matchmarks on the steering wheel assembly and steering main shaft.

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

    3. w/ Steering Heater:


      1. Connect the connector.

    4. Connect each connector to the spiral cable.

  6. INSPECT STEERING WHEEL CENTER POINT

  7. INSTALL STEERING PAD


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01NINU

      Connect the 2 airbag connectors to the steering pad.

      Note


      • When connecting any airbag connector, take care not to damage the airbag wire harness.

      • Be sure to only connect the connectors to each corresponding color.

    4. Push in the 2 airbag connector locks to install the 2 airbag connectors.

    5. Connect the horn connector to the steering pad.

    6. A01NMYA

      Push the steering pad to attach the 3 pins carefully.

      Note


      • Make sure that the pins are securely inserted into the steering holes.

      • Make sure to engage the 2 upper pins first.

      • Make sure that the steering pad is securely installed.

  8. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    1. Engage the claw to install the lower No. 3 steering wheel cover.

  9. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    1. Engage the claw to install the lower No. 2 steering wheel cover.

  10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note


    • Make sure that the cable has been disconnected from the battery terminal for at least 2 seconds before reconnecting the cable.

    • Connect the cable to the negative (-) battery terminal with the front wheels facing straight ahead.

    • Reset the auto away/return function setting to the previous condition by changing the customize parameter Click here.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  11. INSTALL REAR DECK FLOOR BOX


    1. A01NIBL

      Install the rear deck floor box with the 3 clips.

  12. INSPECT STEERING PAD


    1. Make sure that the horn sounds.

      Tech Tips

      If the horn does not sound, inspect the horn system Click here.

  13. INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.