BRAKE CONTROL POWER SUPPLY REMOVAL

Note

While the battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch is turned on. Therefore, when servicing the brake system components, do not depress the brake pedal or open/close the doors while the battery is connected.


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. REMOVE REAR DECK FLOOR BOX


    1. A01NIBL

      Remove the 3 clips and the rear deck floor box.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE DECK BOARD SUB-ASSEMBLY


    1. A01NLRP

      Disengage the 3 fasteners as shown in the illustration.

    2. for Compact Spare Tire:


      1. A01NM7R

        Remove the 2 bolts and remove the deck board sub-assembly.

    3. for Full Size Spare Tire:


      1. A01NM92

        Remove the 2 bolts and remove the deck board sub-assembly.

  5. REMOVE SPARE WHEEL COVER ASSEMBLY (for Compact Spare Tire)


    1. Remove the spare wheel cover assembly.

  6. REMOVE NO. 4 REAR FLOOR BOARD (for Compact Spare Tire)


    1. A01NLSZ

      Disengage the 2 guides and remove the No. 4 rear floor board.

  7. REMOVE NO. 4 REAR FLOOR BOARD (for Full Size Spare Tire)


    1. A01NMV0

      Disengage the 2 guides and remove the No. 4 rear floor board.

  8. REMOVE NO. 3 REAR FLOOR BOARD (for Compact Spare Tire)


    1. A01NIEE

      Disengage the 2 guides and remove the No. 3 rear floor board.

  9. REMOVE NO. 3 REAR FLOOR BOARD (for Full Size Spare Tire)


    1. A01NJCJ

      Disengage the 2 guides and remove the No. 3 rear floor board.

  10. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Remove the tonneau cover assembly.

  11. REMOVE DECK SIDE TRIM BOX LH (for Compact Spare Tire)


    1. A01NNFE

      Remove the 2 clips and the deck side trim box LH.

  12. REMOVE DECK SIDE TRIM BOX LH (for Full Size Spare Tire)


    1. A01NKYS

      Remove the 3 clips and the deck side trim box LH.

  13. REMOVE DECK SIDE TRIM BOX RH (for Compact Spare Tire)


    1. A01NN0A

      Remove the 2 clips and deck side trim box RH.

  14. REMOVE DECK SIDE TRIM BOX RH (for Full Size Spare Tire)


    1. A01NM4K

      Remove the 3 clips and the deck side trim box RH.

  15. REMOVE FRONT DECK FLOOR BOX


    1. A01NN39

      Remove the clip and the front deck floor box.

  16. REMOVE REAR FLOOR FINISH PLATE


    1. A01NMPW

      Disengage the 2 claws, 6 clips and 2 guides, and remove the rear floor finish plate.

  17. REMOVE BRAKE CONTROL POWER SUPPLY WITH BRACKET


    1. A01NKDA

      Remove the 2 clamps.

    2. A01NIH6

      Remove the 3 nuts and the brake control power supply with bracket.

      CAUTION:

      Immediately after removing the brake control power supply from the vehicle, there may be an electrical charge left in the internal capacitor. If planning to inspect the inside of the brake control power supply, leave it as is for more than 24 hours (to discharge it) after removing it from the vehicle. Then, perform the inspection.

    3. A01NMHE

      Disconnect the connector.

  18. REMOVE BRAKE CONTROL POWER SUPPLY ASSEMBLY


    1. A01NK1L

      Remove the 4 bolts, No. 1 control power supply bracket and No. 2 control power supply bracket.

      Note

      Do not drop the brake control power supply. If the brake control power supply has been dropped, replace the brake control power supply with a new one.