Click here

FRONT AXLE HUB BOLT REPLACEMENT

Click here
Click here Click here
Note:

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1341, C1342, C1343 and/or C1344 may be stored. As there is no malfunction, clear the DTC(s).

Tip:

  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

Click here
  1. Click here

    PRECAUTION (w/ Air Suspension)

    Note:

    Be sure to read Precaution thoroughly before servicing (Click here).

  2. Click here

    REMOVE FRONT WHEEL

  3. Click here

    SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY


    1. A01NM8I

      Remove the 2 bolts and separate the front disc brake caliper assembly.

      Note:

      Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.

  4. Click here

    REMOVE FRONT DISC


    1. A01NN99E03

      Remove the front disc.

      Table 1. Text in Illustration
      *1 Matchmark
      Tip:

      Put matchmarks on the disc and the axle hub.

  5. Click here

    REMOVE FRONT AXLE HUB BOLT


    1. A01NLZ2

      Position the front axle hub bolt to be removed as shown in the illustration.

    2. A01NMNLE01

      Temporarily install 2 nuts to the front axle hub bolt as shown in the illustration.

      Table 2. Text in Illustration
      *1 Nut
      Recommended service nut
      Thread diameter: 12.0 mm (0.472 in.)
      Thread pitch: 1.5 mm (0.0591 in.)
      Note:

      Install the nuts to prevent damage to the front axle hub bolts.

    3. Using SST and a brass bar or an equivalent tool to hold the front axle hub, remove the front axle hub bolt.

      09628-10011
  6. Click here

    INSTALL FRONT AXLE HUB BOLT


    1. A01NLZ2

      Position a new front axle hub bolt to be installed as shown in the illustration.

    2. A01NJ5GE03

      Temporarily install the new front axle hub bolt to the front axle hub.

      Table 3. Text in Illustration
      *1 Nut
      *2 Washer

    3. Install a washer and nut to the new front axle hub bolt as shown in the illustration.

      Recommended service nut
      Thread diameter: 12.0 mm (0.472 in.)
      Thread pitch: 1.5 mm (0.0591 in.)
      Tip:

      The thickness of the washer is preferably 5 mm (0.197 in.) or more.

    4. Using a brass bar or an equivalent tool to hold the front axle hub, install the front axle hub bolt by tightening the nut.

      Note:

      • Install the nuts to prevent damage to the front axle hub bolts.

      • Do not damage the threads of the front axle hub bolts.

    5. Remove the 3 nuts and washer from the 3 front axle hub bolts.

  7. Click here

    INSTALL FRONT DISC


    1. A01NN99E03

      Align the matchmarks and install the front disc.

      Table 4. Text in Illustration
      *1 Matchmark
      Note:

      When replacing the disc with a new one, select the installation position where the front disc has minimal runout.

  8. Click here

    INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY


    1. A01NM8I

      Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

      104 N*m 1061 kgf*cm 77 ft.*lbf
  9. Click here

    INSTALL FRONT WHEEL

    103 N*m 1050 kgf*cm 76 ft.*lbf