FRONT DRIVE SHAFT ASSEMBLY REASSEMBLY


  1. INSTALL FRONT DRIVE SHAFT BEARING (for RH Side)


    1. Install a new bearing bracket hole snap ring to the front drive shaft assembly RH.

    2. A01NNDTE07
      Text in Illustration
      *1 Steel Plate

      Using SST, install a new front drive shaft bearing.

      SST
      09527-10011

      Note

      The bearing should be completely installed.

    3. A01NKR3

      Using a snap ring expander, install a new drive shaft hole snap ring.

  2. INSTALL FRONT DRIVE SHAFT DUST COVER


    1. A01NIAZE02

      Using SST and a press, install a new drive shaft dust cover.

      SST
      09527-10011
      09726-40010
      Distance (A)
      26.6 to 27.6 mm (1.05 to 1.08 in.)

      Note


      • The dust cover should be completely installed.

      • Be careful not to damage the dust cover.

  3. INSTALL FRONT DRIVE SHAFT DUST COVER RH


    1. A01NJ92E02

      Using SST and a press, install a new drive shaft dust cover RH until distance (A) from the tip of the center drive shaft to the drive shaft dust cover RH meets the specification.

      SST
      09527-10011
      Distance (A)
      110.5 mm (4.35 in.)

      Note


      • The dust cover should be completely installed.

      • Be careful not to damage the dust cover.

  4. INSTALL FRONT DRIVE SHAFT DUST COVER LH


    1. A01NMFGE03

      Using SST and a press, install a new drive shaft dust cover LH.

      SST
      09527-10011

      Note


      • The dust cover should be completely installed.

      • Be careful not to damage the dust cover.

  5. INSTALL FRONT AXLE OUTBOARD JOINT BOOT (for LH Side)


    1. A01NJZYE03
      Text in Illustration
      *1 Protective Tape

      Wrap the splines of the drive shaft with protective tape to prevent the boot from being damaged.

    2. Install new parts to the outboard joint shaft in the following order:


      1. No. 2 front axle outboard joint boot clamp

      2. Front axle outboard joint boot

      3. Front axle outboard joint boot clamp

    3. Pack the front drive outboard joint shaft and front axle outboard joint boot with grease.

      Grease Capacity
      180 g (6.3 oz.)

  6. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)


    1. Hold the drive shaft in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    2. Install the front axle outboard joint boot clamp onto the front axle outboard joint boot.

    3. A01NL0OE12

      Place SST onto the front axle outboard joint boot clamp.

      SST
      09521-24010

    4. Tighten SST so that the front axle outboard joint boot clamp is pinched.

      Note

      Do not overtighten SST.

    5. A01NJICE01

      Using SST, measure the clearance of the front axle outboard joint boot clamp.

      SST
      09240-00020
      Clearance
      0.5 to 1.5 mm (0.0197 to 0.0591 in.)

      Note

      If the measured value is greater than the specified value, retighten the clamp.

  7. INSTALL NO. 2 FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)


    1. Install the No. 2 front axle outboard joint boot clamp onto the front axle outboard joint boot.

    2. A01NMW0E18

      Place SST onto the No. 2 front axle outboard joint boot clamp.

      SST
      09521-24010

    3. Tighten SST so that the No. 2 front axle outboard joint boot clamp is pinched.

      Note

      Do not overtighten SST.

    4. A01NIGGE08

      Using SST, measure the clearance of the No. 2 front axle outboard joint boot clamp.

      SST
      09240-00020
      Clearance
      0.5 to 1.5 mm (0.0197 to 0.0591 in.)

      Note

      If the measured value is greater than the specified value, retighten the clamp.

  8. INSTALL FRONT DRIVE SHAFT DAMPER


    1. A01NJDZE01
      Text in Illustration
      *A LH
      *B RH

      Install the drive shaft damper to the drive shaft.

    2. Make sure that the damper is on the shaft groove.

    3. Set the distance as specified below.

      Distance
      Distance
      LH 231.0 to 235.0 mm (9.094 to 9.252 in.)
      RH 245.0 to 249.0 mm (9.646 to 9.803 in.)

    4. Hold the drive shaft in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    5. Install a new drive shaft damper clamp onto the drive shaft damper.

      Note

      Be sure to install the clamp in the correct position.

    6. A01NKICE02

      Place SST onto the drive shaft damper clamp.

      SST
      09521-24010

    7. Tighten SST so that the clamp is pinched.

      Note

      Do not overtighten SST.

    8. A01NKZ6

      Using SST, measure the clearance of the drive shaft damper clamp.

      SST
      09240-00020
      Clearance
      0.5 to 1.5 mm (0.0197 to 0.0591 in.)

      Note

      If the measured value is greater than the specified value, retighten the clamp.

  9. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY


    1. A01NIXZE01
      Text in Illustration
      *1 Protective Tape

      Wrap the splines of the drive shaft with protective tape to prevent the boot from being damaged.

    2. Install new parts to the front drive outboard joint shaft assembly in the following order:


      1. Front axle inboard joint boot clamp

      2. Front axle inboard joint boot

      3. No. 2 front axle inboard joint boot clamp

    3. A01NK6CE16
      Text in Illustration
      *1 Matchmark

      Place the beveled side of the tripod joint axial spline toward the front drive outboard joint shaft assembly.

    4. Align the matchmarks placed before removal.

    5. Using a brass bar and a hammer, tap the tripod joint onto the front drive outboard joint shaft assembly.

      Note


      • Do not tap the roller.

      • Be sure to install the tripod joint in the correct direction.

    6. A01NMD7

      Using a snap ring expander, install a new shaft snap ring.

    7. Pack the front drive inboard joint assembly and front axle inboard boot with grease.

      Grease Capacity
      165 g (5.8 oz.)
    8. A01NIVKE20
      Text in Illustration
      *1 Matchmark

      Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.

  10. INSTALL FRONT AXLE INBOARD JOINT BOOT


    1. Install the front axle inboard joint boot to the front drive inboard joint assembly.

    2. A01NLQWE19

      Check whether the drive shaft dimensions are within the following specifications.

      Tech Tips

      The following table shows dimension (A) of the drive shaft.

      Distance
      Distance
      LH 593.4 mm (1.94 ft.)
      RH 934.7 mm (3.06 ft.)

  11. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP


    1. Hold the drive shaft in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    2. Secure the inboard joint boot clamp onto the boot.

    3. A01NIYXE02

      Place SST onto the inboard joint boot clamp.

      SST
      09521-24010

    4. Tighten SST so that the front axle inboard joint boot clamp is pinched.

      Note

      Do not overtighten SST.

    5. A01NJ8LE01

      Using SST, measure the clearance of the front axle inboard joint boot clamp.

      SST
      09240-00020
      Clearance
      0.5 to 1.5 mm (0.0197 to 0.0591 in.)

      Note

      If the measured value is greater than the specified value, retighten the clamp.

  12. INSTALL NO. 2 FRONT AXLE INBOARD JOINT BOOT CLAMP


    1. Hold the inboard joint shaft assembly in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    2. Secure the No. 2 front axle inboard joint boot clamp onto the boot.

    3. A01NK0DE13

      Place SST onto the No. 2 front axle inboard joint boot clamp.

      SST
      09521-24010

    4. Tighten SST so that the No. 2 front axle inboard joint boot clamp is pinched.

      Note

      Do not overtighten SST.

    5. A01NJNPE09

      Using SST, measure the clearance of the No. 2 front axle inboard joint boot clamp.

      SST
      09240-00020
      Clearance
      0.5 to 1.5 mm (0.0197 to 0.0591 in.)

      Note

      If the measured value is greater than the specified value, retighten the clamp.

  13. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING


    1. Install a new front drive shaft hole snap ring.

  14. INSPECT FRONT DRIVE SHAFT ASSEMBLY


    1. A01NLMX

      Check that there is no excessive play in the radial direction of the outboard joint.

    2. Check that the inboard joint slides smoothly in the thrust direction.

    3. Check that there is no excessive play in the radial direction of the inboard joint.

    4. Check the boots for damage.

    5. A01NLQWE04

      Check whether the drive shaft dimensions are within the following specifications.

      Tech Tips

      The following table shows dimension (A) of the drive shaft.

      Distance
      Distance
      LH 593.4 mm (1.94 ft.)
      RH 934.7 mm (3.06 ft.)