SHIFT LEVER INSTALLATION


  1. INSTALL SHIFT LEVER ASSEMBLY

    Note

    Check that the park/neutral position switch and the shift lever are in neutral.


    1. A01NM9CE02
      Text in Illustration
      *1 Lock Nut
      *2 Push in
      *3 Stopper

      Turn the lock nut of the transmission control cable counterclockwise. While holding the lock nut, push in the stopper.

    2. Connect the outer part of the transmission control cable to the shift lever retainer.

      A01NKGJE02
      Text in Illustration
      *1 Shift Lever Retainer *2 Stopper
      *3 Lock Nut - -

      Note

      The lock nut is fully seated against the shift lever retainer.

    3. A01NMG0

      Install the transmission control cable end to the shift lever assembly.

      Note


      • Install the floor shift cable with the uneven surface facing up.

      • Install the cable end all the way to the base of the pin.

    4. A01NIJX

      Install the shift lever assembly with the 4 nuts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    5. Connect the 3 clamps to the shift lever assembly.

    6. Connect the 2 connectors.

  2. INSTALL CONSOLE BOX (for LHD)


    1. A01NJ3FE01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Engage the 3 guides as shown in the illustration.

    2. Engage the 2 clamps.

    3. Install the 3 clips.

    4. Install the console box with the 5 screws <D>.

  3. INSTALL CONSOLE BOX (for RHD)


    1. A01NM8NE01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Engage the 3 guides as shown in the illustration.

    2. Engage the 2 clamps.

    3. Install the 2 clips.

    4. Install the console box with the 5 screws <D>.

  4. INSTALL FRONT CONSOLE BOX COVER


    1. A01NLC6

      Connect the connector.

    2. Engage the 5 guides and 2 clips, and install the front console box cover.

  5. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL


    1. A01NMLC

      Engage the 7 clips to install the lower instrument panel finish panel as shown in the illustration.

  6. INSTALL INSTRUMENT PANEL FINISH PANEL


    1. A01NILC

      Engage the 2 guides, claw and 2 clips to install the instrument panel finish panel as shown in the illustration.

  7. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. Connect each connector.

    2. Engage the 8 clips and 2 guides.

    3. Install the lower instrument panel finish panel sub-assembly with the 2 screws <D>.

    4. A01NMBT

      Engage the 2 claws to close the cover as shown in the illustration.

  8. INSTALL NO. 1 SWITCH HOLE BASE


    1. Connect each connector.

    2. A01NLSK

      Engage the 4 claws and 2 guides to install the No. 1 switch hole base.

  9. INSTALL INSTRUMENT PANEL GARNISH LH


    1. A01NI52

      Engage the 6 clips to install the instrument panel garnish LH.

  10. INSTALL REAR CONSOLE BOX ASSEMBLY


    1. A01NI9XE01

      Engage the 8 guides as shown in the illustration.

      Note

      Make sure to install the rear console box assembly in the direction indicated by the arrow (1). Failure to do so will damage the console box and front seat.

    2. Install the rear console box assembly with the 2 screws and 4 bolts.

  11. INSTALL CONSOLE REAR END PANEL SUB-ASSEMBLY


    1. w/o Rear Seat Entertainment System:


      1. Engage the 5 claws and 6 clips to install the console rear end panel sub-assembly.

    2. w/ Rear Seat Entertainment System:


      1. Connect each connector.

      2. Engage the 5 claws and 6 clips to install the console rear end panel sub-assembly.

  12. INSTALL NO. 2 CONSOLE BOX DUCT


    1. Install the No. 2 console box duct with the 2 screws.

    2. Connect each connector and engage the 2 clamps.

  13. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. Engage the clamp.

    2. Connect each connector.

    3. A01NINT

      Engage the 3 claws and 3 clips.

    4. w/o Seat Heater System:


      1. Connect the connector to the console box hole cover.

    5. w/ Seat Heater System:


      1. Connect the connector.

      2. Engage the 6 claws to install the seat heater switch with console box hole cover.

    6. A01NJIY

      Engage the 4 claws and 4 clips to install the upper console panel sub-assembly.

  14. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A01NIFY

      Turn the shift lever knob sub-assembly clockwise to install the shift lever knob sub-assembly.

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  16. INSPECT SUSPENSION CONTROL SYSTEM (w/ Air Suspension)


    1. Inspect the suspension control system Click here.

  17. INSPECT SHIFT LEVER POSITION


    1. When moving the shift lever from P to R with the power switch on (IG) and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

    2. Turn the power switch on (READY) and make sure that the vehicle moves forward when moving the shift lever from N to D and moves rearward when moving the shift lever to R.

      If the operation cannot be performed as specified, inspect the shift lever position sensor and check the shift lever assembly installation condition.

  18. ADJUST SHIFT LEVER POSITION


    1. Apply the parking brake and move the shift lever to N.

      Note

      Check that the control shaft lever and the shift lever are in neutral.

    2. Remove the No. 1 engine under cover.

    3. A01NIJ4

      Remove the nut from the control shaft lever.

    4. Using a screwdriver, disengage the 4 claws and disconnect the control cable with clip from the control cable bracket.

    5. Remove the clip.

    6. Turn back the boot.

    7. A01NKTIE01
      Text in Illustration
      *1 Slider
      *2 Lock Piece

      Slide the slider of the transmission control cable in the direction indicated by the arrow and pull the lock piece outward.

    8. Install a new clip to the control cable bracket.

    9. A01NL4XE03
      Text in Illustration
      *1 Claw A
      *2 Claw B
      *3 Control Cable

      Install the control cable to the control cable bracket.

      Note


      • Make sure that the claws A on the clip are securely fit into the bracket holes.

      • Make sure that the cable is securely installed inside of the claws B of the clip.

    10. A01NIYFE02
      Text in Illustration
      *1 Lock Piece

      Connect the transmission control cable to the control shaft lever with the nut.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

      Note

      Check that the lock piece is pulled up.

    11. A01NL2JE01
      Text in Illustration
      *1 Lock Piece

      Push the lock piece into the adjuster case.

      Note


      • Check that the shift lever position sensor and the shift lever are in neutral.

      • Securely push in the lock piece until the slider lock is engaged.

    12. Refit the boot.

    13. After adjusting the shift lever position, check the operation and function of the shift lever. If there is a problem, adjust the position again.

    14. Install the No. 1 engine under cover.

  19. INSPECT SHIFT LEVER OPERATION


    1. While moving the shift lever from N to each position, check that the lever moves smoothly and that the shift position indicator comes on properly according to the shift lever position.

    2. Turn the power switch on (READY) and check the following:


      1. When the shift lever is moved to D, the vehicle moves forward.

      2. When the shift lever is moved to R, the vehicle moves in reverse.

        Note

        The vehicle should not move when the shift position indicator is off.

  20. INSTALL REAR DECK FLOOR BOX


    1. A01NIBL

      Install the rear deck floor box with the 3 clips.