Click here

DYNAMIC RADAR CRUISE CONTROL SYSTEM, Diagnostic DTC:C1A50

Click here
Click here Click here
DTC Code DTC Name
C1A50 Brake System
Click here

DESCRIPTION

When the driving support ECU receives an electronically controlled brake system malfunction signal from the skid control ECU via the CAN communication line, DTC C1A50 is stored.

DTC No. DTC Detection Condition Trouble Area
C1A50 When signal malfunction from skid control ECU continues for 1 second while dynamic radar cruise control is operating

  • Electronically controlled brake system

  • Driving support ECU
Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Click here

PROCEDURE


  1. Click here

    READ OUTPUT DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the tester on.

    4. Enter the following menus: Chassis / ABS / VSC / TRC / DTC.

    5. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC is output B

  2. Click here

    CHECK WHETHER DTC OUTPUT RECURS (DTC C1A50)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Clear the DTCs (Click here).

    4. Perform the following to make sure that the DTC detection conditions are met.

      Tip:

      If the detection conditions are not met, the malfunction cannot be detected.


      1. Drive the vehicle at a speed of 40 km/h (25 mph) or more.

      2. Turn the cruise control main switch on.

      3. Push the -SET switch to activate the cruise control.

    5. Enter the following menus: Powertrain / Radar Cruise / DTC.

    6. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC C1A50 is output B

  3. Click here

    USE SIMULATION METHOD TO CHECKClick here

  4. Click here

    REPLACE DRIVING SUPPORT ECU


    1. Replace the driving support ECU (Click here).


  5. Click here

    CHECK WHETHER DTC OUTPUT RECURS (DTC C1A50)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Clear the DTCs (Click here).

    4. Perform the following to make sure that the DTC detection conditions are met.

      Tip:

      If the detection conditions are not met, the malfunction cannot be detected.


      1. Drive the vehicle at a speed of 40 km/h (25 mph) or more.

      2. Turn the cruise control main switch on.

      3. Push the -SET switch to activate the cruise control.

    5. Enter the following menus: Powertrain / Radar Cruise / DTC.

    6. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC C1A50 is output B

  6. Click here

    END

  7. Click here

    REPLACE SKID CONTROL ECU


    1. Replace the skid control ECU (Click here).


  8. Click here

    CHECK WHETHER DTC OUTPUT RECURS (DTC C1A50)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Clear the DTCs (Click here).

    4. Perform the following to make sure that the DTC detection conditions are met.

      Tip:

      If the detection conditions are not met, the malfunction cannot be detected.


      1. Drive the vehicle at a speed of 40 km/h (25 mph) or more.

      2. Turn the cruise control main switch on.

      3. Push the -SET switch to activate the cruise control.

    5. Enter the following menus: Powertrain / Radar Cruise / DTC.

    6. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC C1A50 is output (for LHD) B
      DTC C1A50 is output (for RHD) C

  9. Click here

    END

  10. Click here

    REPLACE POWER MANAGEMENT CONTROL ECU (for LHD)Click here

  11. Click here

    GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEMClick here

  12. Click here

    REPLACE POWER MANAGEMENT CONTROL ECU (for RHD)Click here