FUEL INJECTOR REMOVAL


  1. PRECAUTION (w/ Air Suspension)

    Note

    Be sure to read Precaution thoroughly before servicing Click here.

  2. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work Click here.

  3. DISCHARGE FUEL SYSTEM PRESSURE

    Tech Tips

    Click here

  4. REMOVE REAR DECK FLOOR BOX


    1. A01NIBL

      Remove the 3 clips and the rear deck floor box.

  5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  6. REMOVE AIR CLEANER ASSEMBLY WITH HOSE

    Tech Tips

    Click here

  7. REMOVE INTAKE AIR SURGE TANK ASSEMBLY


    1. A01NL6X

      Disconnect the throttle body assembly connector and wire harness clamp.

    2. A01NLHF

      Disconnect the fuel vapor feed hose.

    3. A01NLNY

      Disconnect the 2 water by-pass hoses.

    4. A01NI9Z

      Disconnect the 5 clamps and separate the main wire.

    5. A01NMP3

      Disconnect the ventilation hose.

    6. A01NM5B

      Disconnect the connector from the manifold absolute pressure sensor.

    7. A01NJD4

      Remove the bolt and separate the No. 1 surge tank stay from the intake air surge tank assembly.

    8. Remove the bolt and separate the throttle body bracket from the intake air surge tank assembly.

    9. A01NKFU

      Remove the 2 nuts from the intake air surge tank assembly.

    10. Using a 5 mm socket hexagon wrench, remove the 4 bolts.

    11. A01NLFD

      Remove the intake air surge tank assembly and 3 air surge tank to intake manifold gaskets.

  8. REMOVE NO. 2 EGR PIPE (w/ EGR System)


    1. A01NI88

      Remove the 2 nuts, 2 bolts, No. 2 EGR pipe and 2 gaskets.

  9. REMOVE EGR DELIVERY CHAMBER


    1. A01NJGE

      Disconnect the 2 water hoses and connector (w/ EGR System).

    2. A01NJDUE01
      Text in Illustration
      *A w/ EGR System
      *B w/o EGR System

      Remove the EGR delivery chamber.

    3. A01NMF8

      Remove the No. 2 intake manifold gasket.

  10. DISCONNECT FUEL TUBE SUB-ASSEMBLY


    1. A01NL6ME01

      Remove the No. 2 fuel pipe clamp.

    2. Pinch the tube connector and pull out the fuel pipe.

      Note


      • Check that there is no dirt or other foreign objects around the connector when disconnecting it. Clean the connector as necessary.

      • It is necessary to prevent dirt or foreign objects from entering the quick connector. If dirt or foreign objects get in the connector, the O-rings may not seal properly.

      • Only disconnect the quick connector by hand.

      • Do not bend, kink or twist the nylon tubes.

      • Protect the connector by covering it with a plastic bag.

      • If the pipe and the connector are stuck, carefully try wiggling or pushing and pulling on the connector to release it. Pull the connector off carefully.

  11. REMOVE FUEL INJECTOR ASSEMBLY


    1. A01NNCF

      Disconnect the 6 fuel injector connectors.

    2. A01NLUY

      Remove the 5 bolts and fuel delivery pipe sub-assembly together with the 6 fuel injectors.

      Note

      Be careful not to drop the fuel injectors when removing the fuel delivery pipe.

    3. A01NKYYE01

      Remove the 6 injector vibration insulators from the intake manifold.

    4. A01NMCS

      Pull out the fuel injectors from the fuel delivery pipe.

      Note

      If the injectors are to be reused, reinstall them to the same cylinder they came from.

    5. A01NM5OE03
      Text in Illustration
      *1 O-ring

      Remove the 6 O-rings from the injectors.