HEATED OXYGEN SENSOR INSTALLATION


  1. INSTALL NO. 2 OXYGEN SENSOR


    1. A01NM6TE01
      Text in Illustration
      *1

      Fulcrum Length

      30 mm

      Using SST, install the No. 2 oxygen sensor to the front exhaust pipe assembly.

      SST
      09224-00010
      Torque:
      without SST
      44 N*m  { 449 kgf*cm, 32 ft.*lbf }
      with SST
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

      Note


      • The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).

      • The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 300 mm (11.81 in.) Click here.

      • The "with SST" torque value is effective when SST is parallel to the torque wrench.

    2. A01NLJF

      Install the wire harness clamp bracket.

  2. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    1. Install a new gasket to the front exhaust pipe assembly.

    2. A01NLY4E01

      Install the front exhaust pipe assembly with the 2 nuts and 2 bolts (B).

      Torque:
      Bolt B
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }
      Nut
      55 N*m  { 561 kgf*cm, 40 ft.*lbf }

    3. Tighten the bolt (A).

      Torque:
      Bolt A
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }
    4. A01NK7A

      Connect the 2 clamps and No. 2 oxygen sensor connector (for Bank 2 Sensor 2).

  3. INSTALL NO. 3 FRONT EXHAUST PIPE SUB-ASSEMBLY


    1. A01NN5JE15
      Text in Illustration
      *1 No. 3 Front Exhaust Pipe Sub-assembly
      *2 Gasket
      *3 Wooden Block

      Using a plastic hammer and wooden block, tap in a new gasket until its surface is flush with the No. 3 front exhaust pipe sub-assembly.

      Note


      • Be sure to install the gasket in the correct orientation.

      • Do not reuse the gasket.

      • Do not damage the gasket.

      • Do not push in the gasket by using the exhaust pipe when connecting it.

    2. Install 2 new gaskets to the No. 3 front exhaust pipe sub-assembly.

    3. Install the No. 3 front exhaust pipe sub-assembly with the 2 bolts and 2 nuts.

      Torque:
      Bolt
      55 N*m  { 561 kgf*cm, 40 ft.*lbf }
      Nut
      55 N*m  { 561 kgf*cm, 40 ft.*lbf }
    4. A01NLB5

      Using a vernier caliper, measure the free length of the compression springs.

      Minimum length
      41.5 mm (1.64 in.)

      If the free length is less than the minimum, replace the compression spring.

    5. A01NLL1

      Install the front No. 3 exhaust pipe sub-assembly with the 2 bolts and 2 compression springs.

      Torque:
      43 N*m  { 440 kgf*cm, 32 ft.*lbf }

  4. INSTALL OXYGEN SENSOR


    1. A01NM25E01
      Text in Illustration
      *1

      Fulcrum Length

      30 mm
      *2

      Fulcrum Length

      300 mm

      Using SST, install the oxygen sensor to the center exhaust pipe assembly.

      SST
      09224-00010
      Torque:
      without SST
      44 N*m  { 449 kgf*cm, 32 ft.*lbf }
      with SST
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

      Note


      • The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).

      • The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 300 mm (11.81 in.) Click here.

      • The "with SST" torque value is effective when SST is parallel to the torque wrench.

    2. A01NMD4

      Connect the wire harness clamp.

    3. A01NITC

      Connect the 2 wire harness clamps and oxygen sensor connector (for Bank 1 Sensor 2).

  5. INSPECT FOR EXHAUST GAS LEAK

  6. INSTALL FRONT FLOOR COVER LH


    1. A01NKA6E01
      Text in Illustration
      *1 Bolt
      *2 Screw

      Connect the 2 clips (B).

    2. Install the front floor cover LH with the 2 screws and 4 bolts.

    3. Install the clip (A).