REPAIR INSTRUCTION

POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

Tilt & Telescopic
Display	Default	Content	Setting
Auto away/Return function	ON	Turn the auto away/return function ON/OFF	ON / OFF

LEXUS PARKING ASSIST-SENSOR SYSTEM (w/ Side Monitor System)

Customizing with the intelligent tester

Warning
Display	Default	Content	Setting	Relevant ECU
Fr Sensor Onset Range	Wide	Sets the detection operation range for the front center sensors.	Narrow or Wide Narrow: 500 mm (19.7 in.) Wide: 1000 mm (39.4 in.)	Parking assist ECU
Rr Sensor Onset Range	Wide	Sets the detection operation range for the rear center sensors.	Narrow or Wide Narrow: 600 mm (23.6 in.) Wide: 1500 mm (59.1 in.)	Parking assist ECU
Keep Sense Buzzer	Avail	Sounds the buzzer when the distance between the vehicle and obstacle does not change for more than 3 seconds.	Not Avail or Avail Not Avail: Not Available Avail: Available	Parking assist ECU
Fr & Rr Buzzer Volume	M2	Changes the buzzer volume setting.	L, M1, M2, M3 or H L: Low volume M1: Medium low volume M2: Medium volume M3: Medium high volume H: High volume	Parking assist ECU

Sensor
Display	Default	Content	Setting	Relevant ECU
Sensor Condition N	Avail	Makes the front sensors available when the shift lever is in N.	Not Avail or Avail Not Avail: Not Available Avail: Available	Parking assist ECU
Reverse Range Front Sensor	Fcrn	Changes the operation setting for the front sensors when the shift lever is in R.	F, Fcrn or F Stop F: All front sensors are available Fcrn: Front corner sensors are available F Stop: All Front sensors are not available	Parking assist ECU
Non P/R Range Rear Sensor	R Stop	Changes the operation setting for the rear sensors when the shift lever is in any position other than P or R.	R, Rcrn or R Stop R: All rear sensors are available Rcrn: Rear corner sensors are available R Stop: All rear sensors are not available	Parking assist ECU

Display
Display	Default	Content	Setting	Relevant ECU
Display Mode	All	The display mode setting (when the LEXUS parking assist-sensor system is normal).	All or Undisp	Parking assist ECU

Customizing with Multi-display

Note

When the customer requests a change in a function, first make sure that the function can be customized.
Be sure to make a note of the current settings before customizing.
When troubleshooting a function, first make sure that the function is set to the default setting.

Turn the power switch on (IG).
Turn the LEXUS parking assist-sensor system on.
Enter the following menus: Setup / Vehicle / LEXUS park assist.

Select the setting by referring to the table below.

Display	Default	Content	Setting	Relevant ECU
Alert volume	3	Sets the buzzer alert volume.	1, 2, 3, 4 or 5 1: Low volume 2: Medium low volume 3: Medium volume 4: Medium high volume 5: High volume	Parking assist ECU
Display	On	The display mode setting (when the LEXUS parking assist-sensor system is normal).	On or Off	Parking assist ECU
Distance Front	Wide	Sets the detection operation range for the front center sensors.	Narrow or Wide Narrow: 500 mm (19.7 in.) Wide: 1000 mm (39.4 in.)	Parking assist ECU
Distance Rear	Wide	Sets the detection operation range for the rear center sensors.	Narrow or Wide Narrow: 600 mm (23.6 in.) Wide: 1500 mm (59.1 in.)	Parking assist ECU

LEXUS PARKING ASSIST-SENSOR SYSTEM (w/o Side Monitor System)

Customizing with the intelligent tester

Warning
Display	Default	Content	Setting	Relevant ECU
Fr Sensor Onset Range	Wide	Sets the detection operation range for the front center sensors.	Narrow or Wide Narrow: 500 mm (19.7 in.) Wide: 1000 mm (39.4 in.)	Clearance warning ECU assembly
Rr Sensor Onset Range	Wide	Sets the detection operation range for the rear center sensors.	Narrow or Wide Narrow: 600 mm (23.6 in.) Wide: 1500 mm (59.1 in.)	Clearance warning ECU assembly
Keep Sense Buzzer	Avail	Sounds the buzzer when the distance between the vehicle and obstacle does not change for more than 3 seconds.	Not Avail or Avail Not Avail: Not Available Avail: Available	Clearance warning ECU assembly
Fr & Rr Buzzer Volume	M2	Changes the buzzer volume setting.	L, M1, M2, M3 or H L: Low volume M1: Medium low volume M2: Medium volume M3: Medium high volume H: High volume	Clearance warning ECU assembly

Sensor
Display	Default	Content	Setting	Relevant ECU
Sensor Condition N	Avail	Makes the front sensors available when the shift lever is in N.	Not Avail or Avail Not Avail: Not Available Avail: Available	Clearance warning ECU assembly
Reverse Range Front Sensor	Fcrn	Changes the operation setting for the front sensors when the shift lever is in R.	F, Fcrn or F Stop F: All front sensors are available Fcrn: Front corner sensors are available F Stop: All Front sensors are not available	Clearance warning ECU assembly
Non P/R Range Rear Sensor	R Stop	Changes the operation setting for the rear sensors when the shift lever is in any position other than P or R.	R, Rcrn or R Stop R: All rear sensors are available Rcrn: Rear corner sensors are available R Stop: All rear sensors are not available	Clearance warning ECU assembly

Display
Display	Default	Content	Setting	Relevant ECU
Display Mode*1	All	The display mode setting (when the LEXUS parking assist-sensor system is normal).	All or Undisp	Clearance warning ECU assembly

*1: This item is used to allow or prevent the LEXUS parking assist-sensor system from being displayed on the multi display assembly. For this model, some vehicles are not equipped with the multi display assembly. For those vehicles, the Display Mode item is not available.

Customizing with Multi-display

Note

When the customer requests a change in a function, first make sure that the function can be customized.
Be sure to make a note of the current settings before customizing.
When troubleshooting a function, first make sure that the function is set to the default setting.

Turn the power switch on (IG).
Turn the LEXUS parking assist-sensor system on.
Enter the following menus: Setup / Vehicle / LEXUS park assist.

Select the setting by referring to the table below.

Display	Default	Content	Setting	Relevant ECU
Alert volume	3	Sets the buzzer alert volume.	1, 2, 3, 4 or 5 1: Low volume 2: Medium low volume 3: Medium volume 4: Medium high volume 5: High volume	Clearance warning ECU assembly
Display	On	The display mode setting (when the LEXUS parking assist-sensor system is normal).	On or Off	Clearance warning ECU assembly
Distance Front	Wide	Sets the detection operation range for the front center sensors.	Narrow or Wide Narrow: 500 mm (19.7 in.) Wide: 1000 mm (39.4 in.)	Clearance warning ECU assembly
Distance Rear	Wide	Sets the detection operation range for the rear center sensors.	Narrow or Wide Narrow: 600 mm (23.6 in.) Wide: 1500 mm (59.1 in.)	Clearance warning ECU assembly

POWER DOOR LOCK CONTROL SYSTEM

Customizing with the intelligent tester

Door Lock
Display	Default	Content	Setting
Unlock Key Twice*1	ON or OFF	Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlocks all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors.	ON or OFF
Auto Lock	ON	Function that locks all doors when the vehicle speed reaches a certain level.	ON or OFF
Auto Lock/Shift	OFF	Function that locks all doors when the shift lever is moved from P to any position other than P while the engine is running and all doors are closed.	ON or OFF
Auto Unlock/Shift	OFF	Function that unlocks all doors when the shift lever is moved to P from any position other than P while the power switch is on (IG).	ON or OFF
All Unlock/Open-Close*1	ON or OFF	Function that unlocks the other doors when the driver door is opened within approximately 43 seconds after the power switch is turned off.	ON or OFF

*1: Default setting differs depending on the country.

Illuminated Entry
Display	Default	Content	Setting
Lighting Time	15 s	Function that changes the lighting time after closing all doors. (It will quickly fade out in case of turning the power switch from off to on (ACC) or on (IG).)	7.5 s, 15 s or 30 s

Customizing with the multi-display (w/ Navigation System)

Turn the power switch on (IG).
Enter the following menus: MENU / Setup / Vehicle / Vehicle customization / Door lock settings.

Select the setting by referring to the table below.

Display	Default	Content	Setting	Relevant ECU
Unlock on second key turn*1	On or Off	Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlock all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors.	On or Off	Main body ECU (Multiplex network body ECU)
Auto lock by speed	On	Function that locks all doors when the vehicle speed reaches a certain level.	On or Off	Main body ECU (Multiplex network body ECU)
Auto lock by shift from P	Off	Function that locks all doors when the shift lever is moved from P to any position other than P while the engine is running and all doors are closed.	On or Off	Main body ECU (Multiplex network body ECU)
Auto unlock by shift to P	On	Function that unlocks all doors when the shift lever is moved to P from any position other than P while the power switch is on (IG).	On or Off	Main body ECU (Multiplex network body ECU)
Auto unlock by driver door*1	On or Off	Function that unlocks the other doors when the driver door is opened within approximately 43 seconds after the power switch is turned off.	On or Off	Main body ECU (Multiplex network body ECU)

*1: Default setting differs depending on the country.

Customizing with the multi-display (w/o Navigation System)

Turn the power switch on (IG).
Enter the following menus: MENU / Setup / Vehicle / Vehicle customization / Door lock settings.

Select the setting by referring to the table below.

Display	Default	Content	Setting	Relevant ECU
Auto lock by speed	On	Function that locks all doors when the vehicle speed reaches a certain level.	On or Off	Main body ECU (Multiplex network body ECU)
Auto lock by shift from P	Off	Function that locks all doors when the shift lever is moved from P to any position other than P while the engine is running and all doors are closed.	On or Off	Main body ECU (Multiplex network body ECU)
Auto unlock by shift to P	On	Function that unlocks all doors when the shift lever is moved to P from any position other than P while the power switch is on (IG).	On or Off	Main body ECU (Multiplex network body ECU)
Auto unlock by driver door*1	On or Off	Function that unlocks the other doors when the driver door is opened within approximately 43 seconds after the power switch is turned off.	On or Off	Main body ECU (Multiplex network body ECU)

*1: Default setting differs depending on the country.

CUSTOMIZING FUNCTION WITH COMBINATION METER ASSEMBLY (POWER DOOR LOCK CONTROL SYSTEM)

Tech Tips

Press and hold the ENTER switch on the steering pad switch assembly when entering an item.
Briefly press the ENTER switch on the steering pad switch assembly when selecting an item.

Turn the power switch on (IG).
Press and hold the ENTER switch on the steering pad switch assembly.

Select the setting by referring to the table below

Display	Default	Content	Setting	Relevant ECU
SPEED SENSITIVE AUTO. LOCK	ON	Function that locks all doors when the vehicle speed reaches a certain level.	ON or OFF	Main body ECU (Multiplex network body ECU)
SHIFT-LINKED AUTOMATIC LOCK	OFF	Function that locks all doors when the shift lever is moved from P to any position other than P while the engine is running and all doors are closed.	ON or OFF	Main body ECU (Multiplex network body ECU)
SHIFT-LINKED AUTOMATIC UNLOCK	ON	Function that unlocks all doors when the shift lever is moved to P from any position other than P while the power switch is on (IG).	ON or OFF	Main body ECU (Multiplex network body ECU)
DRIVER DOOR-LINKED UNLOCK*1	ON or OFF	Function that unlocks the other doors when the driver door is opened within approximately 43 seconds after the power switch is turned off.	ON or OFF	Main body ECU (Multiplex network body ECU)

*1: Default setting differs depending on the country.

Press and hold the ENTER switch on the steering pad switch assembly.
The setting completion screen will be displayed.
Return to the item selection screen.

WIRELESS DOOR LOCK CONTROL SYSTEM

Customizing with the intelligent tester

Wireless Door Lock Control System
Display (item)	Default	Function	Setting
Wireless Control	ON	Function that turns wireless door lock / ON or OFF	ON or OFF
Hazard Answer Back	ON	When the doors are locked by wireless operation, the hazard warning lights flash once. When the doors are unlocked by wireless operation, the hazard warning lights flash twice.	ON or OFF
Open Door Warning*1	ON	The buzzer sounds when lock is pressed when any of the doors are ajar.	ON or OFF
Unlock 2 Operation*2	ON or OFF	Function that unlocks driver door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock.	ON or OFF
Panic Function*3	ON	Function to operate theft deterrent system by continuously pressing panic switch on transmitter for 0.8 seconds	ON or OFF
Auto Lock Time	30 s	Function that regulates the interval between unlocking and automatic relocking of doors	30 s, 60 s or 120 s
Wireless Buzzer Resp*4	ON	Wireless door lock buzzer response / ON or OFF	ON or OFF
P/W Wireless Ope Buzz*5	ON	Wireless power window buzzer response / ON or OFF	ON or OFF
Wireless Buzzer Vol*1	Level 7	Wireless door lock buzzer Volume	Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level 0

*1: w/ Door ajar warning function
*2: Default setting differs depending on the country.
*3: w/ Panic function
*4: w/ Wireless buzzer answer back function
*5: w/ Wireless power window buzzer response function

Illuminated Entry
Display	Default	Content	Setting
Lighting Time	15 s	Changes the lighting time after closing all doors. (It will quickly fade out in case of turning the power switch from off to on (ACC or IG).)	7.5 s, 15 s or 30 s

Customizing with the multi-display (w/ Navigation System)

Turn the power switch on (IG).
Enter the following menus: MENU / Setup / Vehicle / Vehicle customization / Door lock settings.

Select the setting by referring to the table below.

Display	Default	Content	Setting	Relevant ECU
Remote 2-press unlock*1	On or Off	Function that unlocks driver door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock.	On or Off	Main body ECU (Multiplex network body ECU)
Lock/unlock feedback-lights	On	When the doors are locked by wireless operation, the hazard warning lights flash once. When the doors are unlocked by wireless operation, the hazard warning lights flash twice.	On or Off	Main body ECU (Multiplex network body ECU)
Lock/unlock feedback-tone*2	7	Wireless door lock buzzer Volume	Off, 1, 2, 3, 4, 5, 6 or 7	Main body ECU (Multiplex network body ECU)

Display

Default

Content

Setting

Relevant ECU

Remote 2-press unlock*1

On or Off

Function that unlocks driver door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock.

On or Off

Main body ECU (Multiplex network body ECU)

Lock/unlock feedback-lights

On

When the doors are locked by wireless operation, the hazard warning lights flash once.

When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

On or Off

Main body ECU (Multiplex network body ECU)

Lock/unlock feedback-tone*2

7

Wireless door lock buzzer Volume

Off, 1, 2, 3, 4, 5, 6 or 7

Main body ECU (Multiplex network body ECU)

*1: Default setting differs depending on the country.
*2: w/ Door ajar warning function

Customizing with the multi-display (w/o Navigation System)

Turn the power switch on (IG).
Enter the following menus: MENU / Setup / Vehicle / Vehicle customization / Door lock settings.

Select the setting by referring to the table below.

Display	Default	Content	Setting	Relevant ECU
Remote 2-press unlock*1	On or Off	Function that unlocks driver door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock.	On or Off	Main body ECU (Multiplex network body ECU)
Lock/unlock feedback-lights	On	When the doors are locked by wireless operation, the hazard warning lights flash once. When the doors are unlocked by wireless operation, the hazard warning lights flash twice.	On or Off	Main body ECU (Multiplex network body ECU)
Lock/unlock feedback-tone*2	7	Wireless door lock buzzer Volume	Off, 1, 2, 3, 4, 5, 6 or 7	Main body ECU (Multiplex network body ECU)

Display

Default

Content

Setting

Relevant ECU

Remote 2-press unlock*1

On or Off

Function that unlocks driver door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock.

On or Off

Main body ECU (Multiplex network body ECU)

Lock/unlock feedback-lights

On

When the doors are locked by wireless operation, the hazard warning lights flash once.

When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

On or Off

Main body ECU (Multiplex network body ECU)

Lock/unlock feedback-tone*2

7

Wireless door lock buzzer Volume

Off, 1, 2, 3, 4, 5, 6 or 7

Main body ECU (Multiplex network body ECU)

*1: Default setting differs depending on the country.
*2: w/ Door ajar warning function

CUSTOMIZING FUNCTION WITH COMBINATION METER ASSEMBLY (WIRELESS DOOR LOCK CONTROL SYSTEM)

Tech Tips

Press and hold the ENTER switch on the steering pad switch assembly when entering an item.
Briefly press the ENTER switch on the steering pad switch assembly when selecting an item.

Turn the power switch on (IG).
Press and hold the ENTER switch on the steering pad switch assembly

Select the setting by referring to the table below

Display	Default	Content	Setting	Relevant ECU
REMOTE 2-PRESS UNLOCK*1	ON or OFF	Function that unlocks driver door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock.	ON or OFF	Main body ECU (Multiplex network body ECU)
LOCK/UNLOCK ANSWER BACK	ON	When the doors are locked by wireless operation, the hazard warning lights flash once. When the doors are unlocked by wireless operation, the hazard warning lights flash twice.	ON or OFF	Main body ECU (Multiplex network body ECU)
LOCK FEEDBACK VOLUME*2	7	Wireless door lock buzzer volume	0, 1, 2, 3, 4, 5, 6 or 7	Main body ECU (Multiplex network body ECU)

Display

Default

Content

Setting

Relevant ECU

REMOTE 2-PRESS UNLOCK*1

ON or OFF

Function that unlocks driver door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock.

ON or OFF

Main body ECU (Multiplex network body ECU)

LOCK/UNLOCK ANSWER BACK

ON

When the doors are locked by wireless operation, the hazard warning lights flash once.

When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

ON or OFF

Main body ECU (Multiplex network body ECU)

LOCK FEEDBACK VOLUME*2

7

Wireless door lock buzzer volume

0, 1, 2, 3, 4, 5, 6 or 7

Main body ECU (Multiplex network body ECU)

*1: Default setting differs depending on the country.
*2: w/ Door ajar warning function

Press and hold the ENTER switch on the steering pad switch assembly.
The setting completion screen will be displayed.
Return to the item selection screen.

ENTRY AND START SYSTEM (for Entry Function)

Customizing with the intelligent tester

Entry & Start
Tester Display	Default	Content	Setting
Ignition Available Area	All	Function that switches the entry hybrid vehicle control system start detection area	Front or All
Park Wait Time	2.5 s	Function that sets waiting time to permit opening door after door is locked with entry lock function	0.5 s, 1.5 s, 2.5 s, or 5 s
Back Door Opening Operation	Long	Function that opens the back door when the driver has the key and presses back door opener switch assembly (opener switch)	Long, Twice or OFF

Warning
Tester Display	Default	Content	Setting
Key Low Battery Warning	ON	Function that warns driver that key battery is weak	ON or OFF

Customizing with the multi-display (w/ Navigation System)

Turn the power switch on (IG).
Enter the following menus: Setup / Vehicle / Vehicle Customization / Door Lock Settings.

Select the setting by referring to the table below.

Display	Default	Content	Setting	Relevant ECU
Select Doors to Unlock	Driver's Door	Function that sets which doors are unlocked by the entry unlock function.	All Doors or Driver's Door	Certification ECU (smart key ECU assembly)
Entry and Start System	On	Function that enables or disables the entry and start system.	On or Off	Certification ECU (smart key ECU assembly)

Customizing with the multi-display (w/ Audio and Visual System (w/ Multi-display))

Turn the power switch on (IG).
Enter the following menus: Setup / Vehicle.

Select the setting by referring to the table below.

Display	Default	Content	Setting	Relevant ECU
Select doors to unlock	Driver's Door	Function that sets which doors are unlocked by the entry unlock function.	All Doors or Driver's Door	Certification ECU (smart key ECU assembly)
Entry and Start System	On	Function that enables or disables the entry and start system.	On or Off	Certification ECU (smart key ECU assembly)

ENTRY UNLOCK MODE SWITCHING

Note

Because the key (for card type) does not have a wireless transmitter function, it cannot be used to change the entry unlock mode.

To change the vehicle entry unlock mode, make sure that the vehicle power is off and simultaneously push and hold the key lock switch and another key switch for 5 seconds.

When the switches are pressed and held for 5 seconds, the entry door unlock mode changes to the mode that is not currently selected.

Note

After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.
- Driver door unlock mode:
  
  When the driver door touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.
- All door unlock mode:
  
  When any touch sensor is touched, all doors unlock.
The certification ECU (smart key ECU assembly) receives this signal from the door control receiver assembly and changes the entry and start system to the entry unlock mode.

The certification ECU (smart key ECU assembly) sounds the buzzers of the wireless door lock buzzer assembly and combination meter assembly (buzzer) to inform the user that the mode has been changed.

for Australia and New Zealand

Mode	Wireless Door Lock Buzzer Assembly	Combination Meter Assembly (Buzzer)
Driver Door (Default)	Sounds 3 times	Sounds once
All Doors (Customized)	Sounds 2 times	Sounds once

Mode

Wireless Door Lock Buzzer Assembly

Combination Meter Assembly (Buzzer)

Driver Door

(Default)

Sounds 3 times

Sounds once

All Doors

(Customized)

Sounds 2 times

Sounds once

Tech Tips

The procedure only changes the entry unlock mode of the entry and start system. It does not switch the unlocking of the wireless door lock control.

for except Australia and New Zealand

Mode	Wireless Door Lock Buzzer Assembly	Combination Meter Assembly (Buzzer)
Driver Door (Customized)	Sounds 3 times	Sounds once
All Doors (Default)	Sounds 2 times	Sounds once

Mode

Wireless Door Lock Buzzer Assembly

Combination Meter Assembly (Buzzer)

Driver Door

(Customized)

Sounds 3 times

Sounds once

All Doors

(Default)

Sounds 2 times

Sounds once

Tech Tips

The procedure only changes the entry unlock mode of the entry and start system. It does not switch the unlocking of the wireless door lock control.

ELECTRICAL KEY CANCEL

Note

Because the key (for card type) does not have a wireless transmitter function, it cannot be used to perform the key cancel operation.

The electrical key cancel operation disables the following functions:

Entry Unlock/Lock
Entry Hybrid Vehicle Control System Start
Entry Back Door Open
Electrical Key Lock-in Prevention
Warning
Memory Call

The operation procedures are as follows:

Precondition:

Power switch off, driver side door closed and unlocked.
1. Push the unlock switch of the key once.
2. Open the driver door within 5 seconds.
3. Push the unlock switch of the key twice within 5 seconds.
4. Close and open the driver door twice within 30 seconds.
  
  (Driver door: Close → Open → Close → Open)
5. Push the unlock switch of the key twice within 5 seconds.
6. Close and open the driver door within 30 seconds.
  
  (Driver door: Close → Open)
7. Close the driver door within 5 seconds.
  
  When electrical key cancel is activated, the wireless door lock buzzer sounds twice.
  
  To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.

ENTRY AND START SYSTEM (for Start Function)

Customizing with the intelligent tester

Entry & Start
Tester Display	Default	Content	Setting
Ignition Available Area (Entry ignition available area)	All	Function to choose the available area for electrical key to start the hybrid control system and cancel the steering lock.	Front or All
Key Low Battery Warning	ON	Function to warn driver that the key battery is low.	ON or OFF

Customizing with the multi-display (w/ Navigation System)

Turn the power switch on (IG).
Enter the following menus: Setup / Vehicle / Vehicle Customization / Door Lock Settings.

Select the setting by referring to the table below.

Display	Default	Content	Setting	Relevant ECU
Select Doors to Unlock	Driver's Door	Function that sets which doors are unlocked by the entry unlock function.	All Doors or Driver's Door	Certification ECU (smart key ECU assembly)
Entry and Start System	On	Function that enables or disables the entry and start system.	On or Off	Certification ECU (smart key ECU assembly)

Customizing with the multi-display (w/ Audio and Visual System (w/ Multi-display))

Turn the power switch on (IG).
Enter the following menus: Setup / Vehicle.

Select the setting by referring to the table below.

Display	Default	Content	Setting	Relevant ECU
Select Doors to Unlock	Driver's Door	Function that sets which doors are unlocked by the entry unlock function.	All Doors or Driver's Door	Certification ECU (smart key ECU assembly)
Entry and Start System	On	Function that enables or disables the entry and start system.	On or Off	Certification ECU (smart key ECU assembly)

ENTRY AND START SYSTEM (for Start Function) (without Intelligent Tester)

Performing the following procedure disables the entry and start system.

Tech Tips

To start the hybrid control system while the entry and start system is disabled, follow the procedure for when the key battery is low Click here.

The operation procedures are as follows:

Precondition:

Power switch off, driver side door closed and unlocked.
1. Push the unlock switch of the key once.
2. Open the driver door within 5 seconds.
3. Push the unlock switch of the key twice within 5 seconds.
4. Close and open the driver door twice within 30 seconds.
  
  (Driver door: Close → Open → Close → Open)
5. Push the unlock switch of the key twice within 5 seconds.
6. Close and open the driver door within 30 seconds.
  
  (Driver door: Close → Open)
7. Close the driver door within 5 seconds.
  
  When electrical key cancel is activated, the wireless door lock buzzer sounds twice.
  
  To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.

THEFT DETERRENT SYSTEM (w/ Intrusion Sensor)

Theft Deterrent System (w/ Intrusion Sensor)
Display (item)	Default	Function	Setting
Intrusion Win Opened	OFF	This function sets the sensitivity of the intrusion sensor when a door window is open	ON or OFF
Security control with mechanism key	OFF	This function set to be able to release security alarm with the mechanism key	ON or OFF

THEFT DETERRENT SYSTEM (w/o Intrusion Sensor)

Theft Deterrent System (w/o Intrusion Sensor)
Display (item)	Default	Function	Setting
Security control with mechanism key	OFF	This function set to be able to release security alarm with the mechanism key	ON or OFF

LIGHTING SYSTEM (INT)

Customizing with the intelligent tester

Illuminated Entry
Tester Display	Default	Content	Setting	Relevant ECU
Lighting Time	15 s	Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).)	7.5 s, 15 s or 30 s	Main body ECU (Multiplex network body ECU)
I/L when ACC OFF	ON	Lights up power switch illumination, front interior lights, rear interior light, footwell lights and scuff plate lights when the power switch is turned from on (ACC or IG) to off.	ON or OFF
I/L ON W/Door Key Unlock	ON	Lights up power switch illumination, front interior lights, rear interior light, footwell lights and scuff plate lights when doors are unlocked using a mechanical key or door control transmitter.	ON or OFF
Room Light when Aprchd	ON	Lights up the power switch illumination, front interior lights, rear interior light, footwell lights and scuff plate lights when a key enters any actuation area around the doors.	ON or OFF
Center Console Spot Light	ON	Lights up the center console spot light when power switch is turned on (ACC or IG)	ON or OFF
Interior Light Control	ON	Change the interior lights (power switch illumination, front interior lights, rear interior light, footwell lights and scuff plate lights) control.	ON or OFF

Customizing using the Multi-display

Turn the power switch on (IG).
Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Lights Settings.

Select the setting by referring to the table below:

Illuminated Entry
Display	Default	Content	Setting	Relevant ECU
Interior Lights Off Timer	15 sec.	Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).)	Off, 7.5 sec., 15 sec., or 30 sec.	Main body ECU (Multiplex network body ECU)

Customizing using the Combination meter assembly

Tech Tips

Press the UP/DOWN switch on the steering pad switch assembly when changing an item selection.
Press the ENTER switch on the steering pad switch assembly when selecting an item.

Turn the power switch on (IG).
Press and hold the MENU switch on the steering pad switch assembly.

Select the setting by referring to the table below:

Illuminated Entry
Display	Default	Content	Setting	Relevant ECU
INTERIOR LIGHTS OFF TIME ADJUSTMENT	15 s	Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).)	Off, 7.5 s, 15 s, or 30 s	Main body ECU (Multiplex network body ECU)

Press the ENTER switch on the steering pad switch assembly.
The setting completion screen will be displayed.
Return to the item selection screen.

METER / GAUGE SYSTEM

Warning
Tester Display	Default	Content	Setting
Driver Side Seatbelt Warning Buzzer*1	ON	Function to turn on/off the driver side seat belt warning buzzer	ON / OFF
Front Passenger Side Seatbelt Warning Buzzer*1	ON	Function to turn on/off the front passenger side seat belt warning buzzer	ON / OFF

*1: This setting is only valid when the vehicle is driven at 20 km/h (12 mph) or more.

FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

Customizing with the intelligent tester

Main Body
Tester Display	Default	Content	Setting
Seat Move Distance	Standard	Allows customizing of the seat movement distance for the power easy access system.	OFF / Little / Standard

Customizing with the multi-display

Turn the power switch on (IG).
Enter the following menus: Menu / Setup / Vehicle / Vehicle Settings / Vehicle Customization / Other Vehicle Settings

Select the setting by referring to the table below.

Display	Default	Content	Setting	Relevant ECU
Driver's Seat Easy Exit	Full	Allows customizing of the seat movement distance for the power easy access system.	Full / Partial / Off	Front power seat switch (driver side)

CUSTOMIZING FUNCTION WITH COMBINATION METER ASSEMBLY (FRONT POWER SEAT CONTROL SYSTEM (w/ Memory))

Tech Tips

Press the UP/DOWN switch on the steering pad switch assembly when changing an item selection.
Press the ENTER switch on the steering pad switch assembly when selecting an item.

Turn the power switch on (IG).
Press and hold the MENU switch on the steering pad switch assembly.

Select the setting by referring to the table below

Display	Default	Content	Setting	Relevant ECU
DRIVER'S SEAT EASY EXIT	FULL	Allows customizing of the seat movement distance for the power easy access system.	FULL / PARTIAL / OFF	Front power seat switch (driver side)

Press the ENTER switch on the steering pad switch assembly.
The setting completion screen will be displayed.
Return to the item selection screen.

SEAT BELT WARNING SYSTEM

Combination Meter
Tester Display	Default	Content	Setting
Driver Side Seatbelt Warning Buzzer*	ON	Function to sound the seat belt warning buzzer	ON/OFF
Front Passenger Side Seatbelt Warning Buzzer*	ON	Function to sound the seat belt warning buzzer	ON/OFF

*: This setting is only valid when the vehicle is driven at 20 km/h (12 mph) or more.

AIR CONDITIONING SYSTEM

Customizing with the intelligent tester

Air Conditioner
Display (Item)	Default	Content	Setting
Set Temperature Shift	Normal	Function to control with the shifted temperature against the displayed temperature	-2 C, -1 C, Normal, +1 C, +2 C
Evaporator Control	Automatic	Function to set the evaporator control to the automatic position (AUTO) to save power, or to the coldest position (MANUAL) to dehumidify air and to prevent the windows from fogging up	Automatic or Manual
Compressor Mode	Automatic	Function to automatically turn the A/C on by pressing the AUTO button when blower is on and the A/C is off	Automatic or Manual
Air Inlet Mode	Automatic	Function to shift from FRESH mode to RECIRCULATION mode when the A/C is turned on	Automatic or Manual
Foot/DEF Auto Mode	ON	Function to automatically turn the airflow to FOOT/DEF when AUTO mode is on	ON or OFF
Foot/DEF Automatic Blow Up Function	ON	Function to automatically increase the blower level when the defroster is on	ON or OFF
Emission Gas Sensor Shift*1	Normal	Function to change the sensitivity of the smog ventilation sensor	Much Less, Less, Little Less, Normal, Little More, More, Much More
ECO MODE Cancel	OFF	Function to cancel the ECO mode drive when item is on	OFF or ON
Noise and Vibration Reduction	OFF	Function to change speed of the compressor when item is on	OFF or ON

*1: w/ Smog Ventilation Sensor

Customizing with the multi-display (w/ Multi-display)

Turn the power switch on (IG).
Enter the following menus: MENU / Setup / Vehicle / Vehicle settings / Climate settings.

Select the setting by referring to the table below.

Display	Default	Content	Setting	Relevant ECU
Smog Sensor Sensitivity*1	0	Function to change the sensitivity of the smog ventilation sensor	-3, -2, -1, 0, +1, +2, +3	Air conditioning amplifier assembly
Auto A/C Mode	On	Function to automatically turn the A/C on by pressing the AUTO button when blower is on and the A/C is off	On or Off	Air conditioning amplifier assembly
Efficient Ventilation Mode	On	In case of turning the A/C on to cool the cabin down quickly, this is the function to change the mode automatically to RECIRCULATION mode	On or Off	Air conditioning amplifier assembly

*1: w/ Smog Ventilation Sensor

POWER WINDOW CONTROL SYSTEM

Power Window
Tester Display	Default	Content	Setting
Door Key P/W Up	ON	This function is used to close the windows by operating the mechanical key.	ON/OFF
Door Key P/W Down	ON	This function is used to open the windows by operating the mechanical key.	ON/OFF
P/W Up w/ Transmitter	OFF	This function is used to close the windows using the wireless key transmitter.	ON/OFF
P/W Down w/ Transmitter	OFF	This function is used to open the windows using the wireless key transmitter.	ON/OFF
P Window Auto Up	Avail	This function is used to enable or disable the auto up function for the front passenger door window using the power window regulator switch assembly (for front passenger side).	Avail/Not Avl
P Window Auto Up From Driver	Avail	This function is used to enable or disable the remote auto up function for the front passenger door window using the multiplex network master switch assembly.	Avail/Not Avl
RR Window Auto Up	Avail	This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear RH side).	Avail/Not Avl
RR Window Auto Up From Driver	Avail	This function is used to enable or disable the remote auto up function for the rear RH door window using the multiplex network master switch assembly.	Avail/Not Avl
RL Window Auto Up	Avail	This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear LH side).	Avail/Not Avl
RL Window Auto Up From Driver	Avail	This function is used to enable or disable the remote auto up function for the rear LH door window using the multiplex network master switch assembly.	Avail/Not Avl
Close All P/W Function	ON	This function is used to close the windows by suggest mode function.	ON/OFF

SLIDING ROOF SYSTEM

Sliding Roof
Tester Display	Default	Content	Setting
Door Key Related Open*1	ON	Function to manually open sliding roof linked with power windows by holding driver side door key for 1.5 seconds or more to unlock position when power switch is off	ON/OFF
Door Key Related Close*1	ON	Function to manually close sliding roof linked with power windows by holding driver side door key for 1.5 seconds or more to lock position when power switch is off	ON/OFF
Wireless Key Related Open*2	ON	Function to manually open sliding roof linked with power windows by pressing transmitter UNLOCK switch for 2.5 seconds or more when power switch is off	ON/OFF
Wireless Key Related Close*2	ON	Function to manually close sliding roof linked with power windows by pressing transmitter LOCK switch for 2.5 seconds or more when power switch is off	ON/OFF
Door Key Related Operation	Slide	Function to select tilt up or slide open of manual sliding roof operation linked with power windows by holding driver side door key for 1.5 seconds or more to unlock position when power switch is off	Tilt/Slide
Wireless Key Related Operation	Slide	Function to select tilt up or slide open of manual sliding roof operation linked with power windows by pressing on transmitter UNLOCK switch for 2.5 seconds or more when power switch is off	Tilt/Slide

*1: This function is linked with the power window key-linked function. If the power window key-linked function is set to OFF, the sliding roof key-linked function will not operate even when it is set to ON.
*2: This function is linked with the power window wireless transmitter-linked function. If the power window wireless transmitter-linked function is set to OFF, the sliding roof wireless transmitter-linked function will not operate even when it is set to ON.

POWER BACK DOOR SYSTEM

PSD&PBD operation
Tester Display	Default	Content	Setting
PBD SW Operation	0.8 s	Function that turns the power back door closer switch on when a switch is pushed once or held down for 0.8 seconds.	0.8 s or ON
PBD Buzzer*1	OFF	Function that makes the power back door buzzer sound when the power back door is operating.	OFF or ON
Door Unlock with 1 Motion*2	ALL DOORS	Function that selects the door or doors to unlock when the back door is locked and the transmitter switch is pushed to operate the power back door.	Back Door or ALL DOORS
One Motion	(Not Use)2, 4 0.8 s*3	Function that operates the power back door by pushing the transmitter switch when the back door is unlocked.	OFF, 1 Op, 2 Op or 0.8 s
One Motion with Unlock Door*2	0.8 s	Function that operates the power back door by pushing the transmitter switch regardless of the door lock condition.	OFF, 2 Op or 0.8 s
PBD Assist Open Operation*5, 6	OFF	Function that enables or disables the power back door assist open operation . When PBD Assist Open is set to on (enabled) the back door will open automatically when the back door opener switch assembly (opener switch) is operated.	OFF or ON

*1: The warning buzzer that sounds when the power back door is operating cannot be customized (even if this function is set to "OFF", the buzzer will still sound).
*2: w/ Wireless one motion function
*3: w/o Wireless one motion function
*4: "Not Use" is not a setting that can be selected.

Tech Tips

When either "One Motion" or "One Motion with Unlock Door" is selected, the other will display "Not Use".
*5: The power back door assist operation will be linked with the "Back Door Opening Operation" setting of the entry and start system (for entry function) only when all doors are locked. If "Back Door Opening Operation" is set to "OFF", the power back door assist will not operate even if "PBD Assist Open Operation" is set to "ON" Click here.
*6: for models with the "PBD Assist Open Operation" customize setting item.

LIGHTING SYSTEM (LIGHTING EXT)

Customizing with the intelligent tester

Light Control
Display	Default	Content	Setting	Relevant ECU
Response Time*1	Normal	Changes the delay timing of lighting the taillights when going into a tunnel when the light control switch is in the AUTO position.	Long / Normal	Main Body ECU (Multiplex Network Body ECU)
Sensitivity	Normal	Adjusts the sensitivity of the automatic light control system.*A	Light2, Light1, Normal, Dark1 or Dark2
DRL Function	On	ON/OFF of the DRL function	On or Off
Disp Ex ON Sen	Normal	Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*B	Light2, Light1, Normal, Dark1 or Dark2
Disp Ex OFF Sen	Normal	Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*C	Light2, Light1, Normal, Dark1 or Dark2
Follow Me Home Lighting Time*2	30 s	Sets up the headlight lighting time after the power switch off.	30 s, 60 s, 90 s or 120 s
Light up Clearance Lights at Door Unlock Function	ON	This function turns on the parking lights and the taillights for 15 seconds when the doors are unlocked by the smart key or the wireless key.	ON or OFF
Lane CHG Flash CNT	3 times	Changes the lane change flashing times	OFF, 3 times, 5 times, 7 times, 9 times or 11 times

*1: except European Model
*2: for European Model

Tech Tips

The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.

*A
Sensitivity of the automatic light control system
Setting	Dark2	Dark1	Normal	Light1	Light2

*B
Brightness level required to dim the lights
Setting	DARK2	DARK1	NORMAL	LIGHT1	LIGHT2

*C
Brightness level required to cancel the dimming of the lights
Setting	DARK2	DARK1	NORMAL	LIGHT1	LIGHT2

Illuminated Entry
Tester Display	Default	Content	Setting	Relevant ECU
Mirr-Foot-Lgt Approached	ON	Lights up the door mirror foot lights when a key enters any actuation area around the doors.	ON or OFF	Main Body ECU (Multiplex Network Body ECU)
Mirr-Foot-Lgt Unlocked	ON	Lights up door mirror foot lights when doors are unlocked using a mechanical key or door control transmitter.	ON or OFF
Mirror Foot Lighting Time	15 s	Changes the lighting time of the door mirror foot lights.	7.5 s, 15 s, 30 s or 0 s
Exterior Light Control	ON	Changes the door mirror foot light control.	ON or OFF

Customizing with the Multi-display

Turn the power switch on (IG).
Enter the following menus: MENU / Setup / Vehicle / Vehicle customization / Light settings or Other vehicle settings.

Select the setting by referring to the table below.

Light settings
Display	Default	Content	Setting	Relevant ECU
Headlamps-On Sensitivity	0	Adjusts the sensitivity of the automatic light control system.*A	-2, -1, 0, +1 or +2	Main Body ECU (Multiplex Network Body ECU)
Daytime Running Lights	On	ON/OFF of the DRL function	On or Off
Exterior Lights Off Timer	15 sec.	Changes the lighting time of the door mirror foot lights.	Off, 7.5 sec., 15 sec. or 30 sec.

Other vehicle settings
Display	Default	Content	Setting	Relevant ECU
Lane change signal flashes	3	Changes the lane change flashing times	OFF, 3, 5, 7, 9, or 11	Main Body ECU (Multiplex Network Body ECU)

Tech Tips

The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.

*A
Sensitivity of the automatic light control system
Setting	-2	-1	0	+1	+2

Customizing using the combination meter assembly

Tech Tips

Press the UP/DOWN switch on the steering pad switch assembly when changing the displayed item and item settings.
Press the ENTER switch on the steering pad switch assembly when selecting an item.

Turn the power switch on (IG).
Press and hold the MENU switch on the steering pad switch assembly.

Select the setting by referring to the table below:

Display	Default	Content	Setting	Relevant ECU
LIGHT SENSOR SENSITIVITY	0	Adjusts the sensitivity of the automatic light control system.*A	-2, -1, 0, +1 or +2	Main Body ECU (Multiplex Network Body ECU)
DAYTIME RUNNING LIGHTS	ON	ON/OFF of the DRL function	ON or OFF
EXTERIOR LIGHTS OFF TIME ADJUSTMENT	15 s	Changes the lighting time of the door mirror foot lights.	OFF, 7.5 s, 15 s or 30 s

Tech Tips

The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.

*A
Sensitivity of the automatic light control system
Setting	-2	-1	0	+1	+2

Press the ENTER switch on the steering pad switch assembly.
The setting completion screen will be displayed.
Return to the item selection screen.

REPAIR INSTRUCTION CUSTOMIZE PARAMETERS