NAVIGATION SYSTEM Display does not Dim when Light Control Switch is Turned ON

DESCRIPTION

When the navigation system is activated with the light control switch in the tail or head position, before AVC-LAN communication is established, the multi-display assembly dims the display according to the illumination signal received via a direct line.

After AVC-LAN communication is established, the multi-display assembly dims the display according to a dimmer signal sent via AVC-LAN communication.

The multi-media module receiver assembly switches between the daytime screen and night screen on the multi-display according to the illumination signal input.

WIRING DIAGRAM

A01NI9LE07

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CONFIRM SYMPTOMS


    1. Check the symptoms that occur by viewing the display.

      Result
      Result Proceed to
      There is a delay until the display dims after the navigation system is activated with the light control switch in the tail or head position. A
      The display dims for a moment and then becomes bright after the navigation system is activated with the light control switch in the tail or head position. B
      When the light control switch is set to the tail or head position, the display dims but does not switch to the night screen. B
      When the light control switch is set to the tail or head position, the display neither dims nor switches to the night screen. C

      Tech Tips


      • When the navigation system is activated with the light control switch in the tail or head position, before AVC-LAN communication is established, the multi-display assembly dims the display according to the illumination signal received via a direct line.

      • After AVC-LAN communication is established, the multi-display assembly dims the display according to a dimmer signal sent via AVC-LAN communication.

      • The multi-media module receiver assembly switches between the daytime screen and night screen on the multi-display according to the illumination signal input.


    B

    CHECK IMAGE QUALITY SETTING Click here

    C

    GO TO LIGHTING SYSTEM Click here

    A

  2. CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)


    1. Disconnect the G2 multi-display assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G2-13 (GND1) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G2-2 (ILL) - G2-13 (GND1)

      Power switch off

      Light control switch in tail or head position

      		 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  3. CHECK IMAGE QUALITY SETTING


    1. A01NKBGE01
      Text in Illustration
      *a Example

      Display the "Display" screen.

    2. Turn the light control switch to the tail or head position.

    3. Check if "Day Mode" setting on the display adjustment screen is on.

      Result
      Result Proceed to
      "Day Mode" setting is on A
      "Day Mode" setting is off B

    B

    CHECK VEHICLE SIGNAL (OPERATION CHECK) Click here

    A

    TURN "Day Mode" SETTING OFF

  4. CHECK VEHICLE SIGNAL (OPERATION CHECK)


    1. A01NJ1P

      Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal in Operation Check Click here.

    2. Check that the display changes between ON and OFF according to the light control switch operation.

      OK
      Light Control Switch Display
      Tail or head ON
      Off OFF

      Tech Tips

      The display is updated once per second. It is normal for the display to lag behind the actual switch operation.


    NG

    CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL) Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  5. CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)


    1. Disconnect the G35 multi-media module receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G35-12 (GND1) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G35-14 (ILL+) - G35-12 (GND1)

      Power switch off

      Light control switch in tail or head position

      		 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here