RADIO RECEIVER REMOVAL


  1. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A01NMB2

      Turn the shift lever knob sub-assembly counterclockwise and remove the shift lever knob sub-assembly.

  2. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A01NIU0

      Move the shift lever to N.

    2. Pull the upper console panel sub-assembly in the direction indicated by the arrow to disengage the 4 claws and 4 clips.

    3. w/o Seat Heater System:


      1. Disconnect the connector from the console box hole cover.

    4. A01NJCF

      w/ Seat Heater System:


      1. Disengage the 6 claws.

      2. Disconnect the connector and remove the seat heater switch with console box hole cover.

    5. A01NN09

      Pull the upper console panel sub-assembly in the direction indicated by the arrow to disengage the 3 claws and 3 clips.

    6. Disconnect each connector.

    7. Disengage the clamp and remove the upper console panel sub-assembly.

  3. REMOVE INSTRUMENT PANEL GARNISH LH


    1. A01NJH3

      Using moulding remover B, disengage the 6 clips and remove the instrument panel garnish LH as shown in the illustration.

  4. REMOVE NO. 1 SWITCH HOLE BASE


    1. A01NJL9

      Push the No. 1 switch hole base in the direction indicated by the arrow to disengage the 4 claws and 2 guides.

    2. Disconnect each connector and remove the No. 1 switch hole base.

  5. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A01NL83

      Disengage the 2 claws and open the cover as shown in the illustration.

    2. A01NLP9

      Remove the 2 screws <D>.

    3. Disengage the 8 clips and 2 guides.

    4. Disconnect each connector and remove the lower instrument panel finish panel sub-assembly.

  6. REMOVE INSTRUMENT PANEL FINISH PANEL


    1. A01NKT2

      Pull the instrument panel finish panel in the direction indicated by the arrow to disengage the claw, 2 clips and 2 guides, and remove the instrument panel finish panel.

  7. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL


    1. A01NJY6

      Pull the lower instrument panel finish panel in the direction indicated by the arrow to disengage the 7 clips and remove the lower instrument panel finish panel.

  8. REMOVE RADIO RECEIVER ASSEMBLY WITH REGISTER

    Note


    • The 4 bolts of the radio receiver assembly with register are installed though the service holes at the bottom in the instrument panel. Make sure to check all of them.

    • If the radio receiver assembly with register is pulled without removing the 4 bolts, it may result in damage to the radio receiver assembly with register.


    1. A01NJ4NE01
      Text in Illustration
      *1 Service Hole

      Remove the 4 bolts.

    2. Disengage the 7 clips.

    3. Disconnect each connector and remove the radio receiver assembly with register.

  9. REMOVE HAZARD WARNING SIGNAL SWITCH ASSEMBLY


    1. A01NJ0G

      Disengage the clamp.

    2. Using a screwdriver, disengage the 2 claws and remove the hazard warning signal switch assembly.

  10. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A01NLMN

      Disengage the 5 claws and remove the No. 3 instrument panel register assembly.

  11. REMOVE NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A01NIDG

      Disengage the 5 claws and remove the No. 4 instrument panel register assembly.

  12. REMOVE RADIO RECEIVER ASSEMBLY