AUDIO AND VISUAL SYSTEM (w/ Multi-display) Microphone Circuit between Microphone and Radio Receiver

DESCRIPTION

• The radio receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

• Using this circuit, the radio receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio receiver assembly.

WIRING DIAGRAM

INSPECTION PROCEDURE

PROCEDURE

1. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

   
   

   1. Disconnect the G37 radio receiver assembly connector.

   2. Disconnect the T10 map light assembly (telephone microphone assembly) connector.

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition G37-4 (MACC) - T10-33 (MACC) Always Below 1 Ω G37-5 (MIN+) - T10-34 (MCO+) Always Below 1 Ω G37-19 (MIN-) - T10-35 (MCO-) Always Below 1 Ω G37-6 (SNS2) - T10-36 (SNS2) Always Below 1 Ω G37-4 (MACC) - Body ground Always 10 kΩ or higher G37-5 (MIN+) - Body ground Always 10 kΩ or higher G37-19 (MIN-) - Body ground Always 10 kΩ or higher G37-18 (SGND) - Body ground Always 10 kΩ or higher G37-6 (SNS2) - Body ground Always 10 kΩ or higher

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

2. INSPECT RADIO RECEIVER ASSEMBLY

   
   

   1. Reconnect the G37 radio receiver assembly connector.

   2. Reconnect the T10 map light assembly (telephone microphone assembly) connector.

   3. 

      Text in Illustration

      *a	Component with harness connected (Radio Receiver Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition G37-4 (MACC) - Body ground Power switch on (ACC) 4 to 6 V

   4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition G37-18 (SGND) - Body ground Always Below 1 Ω G37-19 (MIN-) - Body ground Always Below 1 Ω

   
   

   NG

   REPLACE RADIO RECEIVER ASSEMBLY Click here

   OK

3. INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

   
   

   1. Disconnect the T10 map light assembly (telephone microphone assembly) connector.

   2. 

      Text in Illustration

      *a	Component without harness connected (Map Light Assembly (Telephone Microphone Assembly))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition T10-36 (SNS2) - T10-35 (MCO-) Always Below 1 Ω

   
   

   NG

   REPLACE TELEPHONE MICROPHONE ASSEMBLY Click here

   OK

4. INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

   
   

   1. Reconnect the G37 radio receiver assembly connector.

   2. Reconnect the T10 map light assembly (telephone microphone assembly) connector.

   3. Turn the power switch on (ACC).

   4. 

      Text in Illustration

      *a	Component with harness connected (Map Light Assembly (Telephone Microphone Assembly))

      Connect an oscilloscope to terminals 34 (MCO+) and 35 (MCO-) of the T10 map light assembly (telephone microphone assembly) connector.

   5. Check the waveform of the telephone microphone assembly using the oscilloscope.

      Result
      Result Proceed to A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output A A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output B

   
   

   B

   REPLACE TELEPHONE MICROPHONE ASSEMBLY Click here

   A

   PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

5. REPLACE TELEPHONE MICROPHONE ASSEMBLY

   
   

   1. Replace the telephone microphone assembly Click here.

   2. Check if the same malfunction recurs.

      Result
      Result Proceed to Malfunction does not recur (returns to normal) A Malfunction recurs B

   
   

   B

   REPLACE MAP LIGHT ASSEMBLY Click here

   A

   END