Click here

AUDIO AND VISUAL SYSTEM (w/ Multi-display), Diagnostic DTC:B15D3

Click here
Click here Click here
DTC Code DTC Name
B15D3 Stereo Component Amplifier Disconnected
Click here

DESCRIPTION

The radio receiver assembly and stereo component amplifier assembly are connected by the AVC-LAN communication line.

When an AVC-LAN communication error occurs between the radio receiver assembly and stereo component amplifier assembly, this DTC will be stored.

DTC No. DTC Detection Condition Trouble Area
B15D3

When either condition below is met:


  • Stereo component amplifier assembly is/was not connected while the power switch is/was on (IG) or on (ACC).

  • Communication between the master unit and the stereo component amplifier assembly is not possible when the engine is/was started.

  • Stereo component amplifier assembly power source circuit

  • AVC-LAN circuit between radio receiver assembly and stereo component amplifier assembly

  • Stereo component amplifier assembly

  • Radio receiver assembly

  • Harness or connector
Tip:

The radio receiver assembly is the master unit.

Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Note:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Click here

PROCEDURE


  1. Click here

    CHECK DTC


    1. If DTC B15C3 is output, perform the troubleshooting of DTC B15C3 first.

      Result
      Result Proceed to
      DTC B15C3 is not output A
      DTC B15C3 is output B

  2. Click here

    CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Check that optional components (including associated wiring) which generate radio waves are not installed.

      Result
      Result Proceed to
      Optional components (including associated wiring) are installed. A
      Optional components (including associated wiring) are not installed. B
      Tip:

      • Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

      • This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.


  3. Click here

    REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Remove optional components (including associated wiring).

      Note:

      Do not remove optional components or associated wiring without the permission of the customer.


  4. Click here

    CHECK DTC


    1. Clear the DTCs (Click here).

    2. Recheck for DTCs and check that no DTCs are output.

      OK
      No DTCs are output.

  5. Click here

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)


    1. Disconnect the O33 and O42 stereo component amplifier assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O42-3 (GND) - Body ground Always Below 1 Ω
      O42-18 (GND2) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O42-1 (+B) - O42-3 (GND) Power switch off 11 to 14 V
      O42-16 (+B2) - O42-3 (GND) Power switch off 11 to 14 V
      O33-12 (ACC) - O42-3 (GND) Power switch on (ACC) 11 to 14 V

  6. Click here

    CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)


    1. Disconnect the G36 radio receiver assembly connector.

    2. Disconnect the O33 stereo component amplifier assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G36-5 (TX2+) - O33-8 (TX+) Always Below 1 Ω
      G36-15 (TX2-) - O33-7 (TX-) Always Below 1 Ω
      G36-5 (TX2+) - Body ground Always 10 kΩ or higher
      G36-15 (TX2-) - Body ground Always 10 kΩ or higher

  7. Click here

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY


    1. Replace the stereo component amplifier assembly (Click here).

    2. Clear the DTCs (Click here).

    3. Recheck for DTCs and check that no DTCs are output.

      OK
      No DTCs are output.

  8. Click here

    END

  9. Click here

    END

  10. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  11. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  12. Click here

    REPLACE RADIO RECEIVER ASSEMBLYClick here

  13. Click here

    GO TO DTC "B15C3"Click here