PARKING BRAKE ASSEMBLY REASSEMBLY


  1. INSTALL PARKING BRAKE SHOE HOLD DOWN SPRING PIN


    1. A01NLOJ

      Install the parking brake shoe hold down spring pin (for front side).

    2. A01NLZK

      Install the parking brake shoe hold down spring pin (for rear side).

  2. APPLY HIGH TEMPERATURE GREASE


    1. A01NLQA

      Apply high temperature grease to the areas of the backing plate which make contact with the shoe as shown in the illustration.

  3. INSTALL PARKING BRAKE SHOE GUIDE PLATE SET BOLT


    1. Apply adhesive to the threads of the parking brake shoe guide plate set bolt.

      Adhesive
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
    2. A01NMGT

      Install the parking brake shoe guide plate and parking brake shoe guide plate set bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  4. INSTALL PARKING BRAKE SHOE LEVER


    1. Apply high temperature grease to the areas of the parking brake shoe lever which make contact with the No. 2 parking brake shoe assembly.

    2. A01NMTO

      Install the parking brake shoe lever and shim to the No. 2 parking brake shoe assembly with a new C-washer as shown in the illustration.

    3. A01NMM6

      Using a feeler gauge, measure the clearance between the No. 2 parking brake shoe assembly and parking brake shoe lever.

      Standard clearance
      Less than 0.35 mm (0.0138 in.)

      If the clearance is not as specified, replace the shim with one of the appropriate size.

      Part No. Shim Thickness
      90564-09184 0.3 mm (0.0118 in.)
      90564-09185 0.6 mm (0.0236 in.)
      90564-09186 0.9 mm (0.0354 in.)

  5. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY WITH PARKING BRAKE SHOE LEVER


    1. A01NKEE

      Using needle-nose pliers, connect the No. 3 parking brake cable assembly to the parking brake shoe lever as shown in the illustration.

      Note

      Be careful not to damage the No. 3 parking brake cable assembly.

  6. INSTALL NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING


    1. A01NLGD

      Install the No. 2 parking brake shoe return tension spring to the No. 2 parking brake shoe assembly.

  7. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. A01NLPK

      Connect the No. 2 parking brake shoe return tension spring to install the No. 1 parking brake shoe assembly.

  8. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET


    1. A01NISG

      Apply high temperature grease to the parking brake shoe adjusting screw set as shown in the illustration.

    2. A01NLSF

      Install the parking brake shoe adjusting screw set.

  9. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY


    1. A01NL20

      Install the No. 2 parking brake shoe assembly to the backing plate with the No. 1 parking brake shoe hold down spring cup and parking brake shoe hold down spring.

  10. INSTALL PARKING BRAKE SHOE LEVER STRUT


    1. A01NJJB

      Install the parking brake shoe lever strut and parking brake shoe strut compression spring.

  11. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. A01NN7F

      Install the No. 1 parking brake shoe assembly to the backing plate with the No. 1 parking brake shoe hold down spring cup and parking brake shoe hold down spring.

  12. INSTALL NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING


    1. A01NJU7

      Install the 2 No. 1 parking brake shoe return tension springs.

      Tech Tips

      First install the front side spring and then the rear side spring.

  13. CHECK PARKING BRAKE INSTALLATION


    1. Check that each part is installed properly.

      A01NMGPE01

      Note

      There should be no oil or grease on the friction surfaces of the shoe lining and disc.

  14. INSTALL REAR DISC


    1. A01NM6FE01
      Text in Illustration
      *1 Matchmark

      Align the matchmarks and install the rear disc.

      Note

      When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.

  15. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

  16. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY


    1. A01NLTQ

      Install the rear disc brake caliper assembly with the 2 bolts.

      Torque:
      78 N*m  { 799 kgf*cm, 58 ft.*lbf }

  17. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  18. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL (for LHD)


    1. Remove the No. 1 instrument panel under cover sub-assembly Click here.

    2. Completely release the parking brake pedal.

    3. A01NKQ7E01
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Loosen the lock nut and the adjusting nut to completely release the parking brake cable.

    4. Remove the rear wheels.

    5. Temporarily install the hub nuts to the hub bolts.

      Tech Tips

      Securely install the hub nuts to the rear disc.

    6. Remove the parking brake shoe adjusting hole plug.

    7. A01NLK9E04
      Text in Illustration
      *1 Expand
      *2 Contract

      Turn the shoe adjuster and expand the shoe until the disc locks.

    8. Turn and contract the shoe adjuster until the disc can rotate smoothly.

      Standard
      Returns 8 notches.

    9. Check that there is no brake drag against the shoe.

    10. Install the parking brake shoe adjusting hole plug.

    11. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

      Parking brake pedal travel
      7 to 10 notches at 300 N (31 kgf, 67.5 lbf)
    12. A01NKQ7E01
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    13. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

    14. Check that there is no brake drag against the shoe.

    15. Remove the hub nuts from the hub bolts.

    16. Install the rear wheels.

      Torque:
      103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

    17. Install the No. 1 instrument panel under cover sub-assembly Click here.

  19. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL (for RHD)


    1. Remove the No. 1 instrument panel under cover sub-assembly Click here.

    2. Completely release the parking brake pedal.

    3. A01NKU0E01
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Loosen the lock nut and the adjusting nut to completely release the parking brake cable.

    4. Remove the rear wheels.

    5. Temporarily install the hub nuts to the hub bolts.

      Tech Tips

      Securely install the hub nuts to the rear disc.

    6. Remove the shoe adjusting hole plug.

    7. A01NLK9E04
      Text in Illustration
      *1 Expand
      *2 Contract

      Turn the shoe adjuster and expand the shoe until the disc locks.

    8. Turn and contract the shoe adjuster until the disc can rotate smoothly.

      Standard
      Returns 8 notches.

    9. Check that there is no brake drag against the shoe.

    10. Install the shoe adjusting hole plug.

    11. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

      Parking brake pedal travel
      7 to 10 notches at 300 N (31 kgf, 67.5 lbf)
    12. A01NKU0E01
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    13. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

    14. Check that there is no brake drag against the shoe.

    15. Remove the hub nuts from the hub bolts.

    16. Install the rear wheels.

      Torque:
      103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

    17. Install the No. 1 instrument panel under cover sub-assembly Click here.