Click here

PARKING BRAKE PEDAL (for RHD) REMOVAL

Click here
Click here Click here
CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

Click here
  1. Click here

    PRECAUTION (w/ Navigation System for HDD)

    Note:

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Table 1. Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.
  2. Click here

    PRECAUTION (w/ Air Suspension)

    Note:

    Be sure to read Precaution thoroughly before servicing (Click here).

  3. Click here

    REMOVE FRONT SEAT ASSEMBLY LH

    Tip:

    Refer to the instructions for Removal of the front seat assembly (Click here).

  4. Click here

    REMOVE REAR CONSOLE BOX ASSEMBLY

    Tip:

    Refer to the instructions for Removal of the rear console box assembly (Click here).

  5. Click here

    REMOVE BRAKE PEDAL SUPPORT ASSEMBLY

    Tip:

    Refer to the instructions for Removal of the brake pedal support assembly (Click here).

  6. Click here

    REMOVE INSTRUMENT PANEL FINISH PANEL

    Tip:

    This is symmetrical to the LHD model (Click here).

  7. Click here

    REMOVE FRONT CONSOLE BOX COVER


    1. A01NJ78

      Using moulding remover A, disengage the 2 clips and 5 guides.

    2. Disconnect the connector and remove the front console box cover.

  8. Click here

    REMOVE CONSOLE BOX


    1. A01NJHE

      Remove the 5 screws <D>.

    2. A01NN20E01

      Disengage the 2 clamps.

      Table 2. Text in Illustration
      *1 Clamp
      *2 Guide

    3. Remove the 2 clips.

    4. Disengage the 3 guides and remove the console box as shown in the illustration.

  9. Click here

    REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01NJ04

      Disengage the 7 claws, 4 clips and guide, and remove the front door scuff plate LH.

      Tip:

      A part of the clip remains on the vehicle side.

    2. w/ Illumination:


      1. Disconnect the connector.

  10. Click here

    REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01NK5N

      Remove the clip.

    2. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  11. Click here

    REMOVE REAR NO. 2 AIR DUCT


    1. Turn back the front floor carpet.

    2. A01NNFN

      Remove the clip and rear No. 2 air duct.

  12. Click here

    REMOVE REAR NO. 1 AIR DUCT


    1. A01NJ67

      Disengage the wire harness clamp.

    2. Remove the rear No. 1 air duct.

  13. Click here

    LOOSEN ADJUSTING NUT


    1. A01NKU0E01

      Remove the lock nut and loosen the adjusting nut.

      Table 3. Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut
  14. Click here

    REMOVE CENTER FRONT FLOOR COVER


    1. A01NIV6

      Remove the 7 bolts and 2 screws.

    2. A01NJ8M

      Disengage the 3 clips to remove the center front floor cover.

  15. Click here

    REMOVE REAR ENGINE SERVICE COVER ASSEMBLY


    1. A01NK1F

      Remove the 2 bolts and rear engine service cover assembly.

  16. Click here

    SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. A01NLJA

      Separate the No. 3 parking brake cable assembly from the parking brake equalizer.

  17. Click here

    SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY

    Tip:

    Perform the same procedure as for the No. 3 parking brake cable assembly.

  18. Click here

    REMOVE PARKING BRAKE EQUALIZER


    1. A01NITD

      Slide the rubber boot as shown in the illustration.

    2. A01NMHQ

      Remove the parking brake equalizer from the No. 1 parking brake cable assembly as shown in the illustration.

  19. Click here

    REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY


    1. A01NL1C

      Remove the 2 bolts and 3 nuts, and separate the No. 1 parking brake cable assembly.

    2. Remove the clamp.

    3. A01NL8E

      Pull out the No. 1 parking brake cable assembly toward the cabin.

    4. A01NIH1

      Disconnect the parking brake switch connector.

    5. A01NJLO

      Remove the 3 nuts and the parking brake control pedal assembly.