BRAKE PEDAL (for RHD) REMOVAL


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

  2. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.

  3. REMOVE REAR DECK FLOOR BOX


    1. A01NIBL

      Remove the 3 clips and the rear deck floor box.

  4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  6. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  7. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A01NL7O

      Remove the 2 screws <D>.

    2. A01NKQB

      Disengage the claw and 2 guides as shown in the illustration.

    3. Disconnect each connector.

    4. Disengage each clamp and remove the No. 1 instrument panel under cover sub-assembly.

  8. REMOVE INSTRUMENT PANEL GARNISH RH (w/o Airbag Cut Off Switch)

    Tech Tips

    Use the same procedure as for the LH side.

  9. REMOVE INSTRUMENT PANEL GARNISH RH (w/ Airbag Cut Off Switch)


    1. A01NJRN

      Using moulding remover B, disengage the 6 clips as shown in the illustration.

    2. Disconnect the connector and remove the instrument panel garnish RH.

  10. REMOVE NO. 1 SWITCH HOLE BASE


    1. A01NJL9

      Push the No. 1 switch hole base in the direction indicated by the arrow to disengage the 4 claws and 2 guides.

    2. Disconnect each connector and remove the No. 1 switch hole base.

  11. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A01NL83

      Disengage the 2 claws and open the cover as shown in the illustration.

    2. A01NLP9

      Remove the 2 screws <D>.

    3. Disengage the 8 clips and 2 guides.

    4. Disconnect each connector and remove the lower instrument panel finish panel sub-assembly.

  12. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY

    CAUTION:

    When storing the driver side knee airbag assembly, keep the airbag deployment side facing upward.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01NLY6

      Remove the 4 bolts.

    4. Disengage the 2 claws and 2 hooks to separate the driver side knee airbag assembly.

    5. A01NJ5IE01

      Disengage the claw to remove the hood lock control cable.

    6. Using a screwdriver with the tip wrapped with protective tape, disconnect the airbag connector to remove the driver side knee airbag assembly.

      Text in Illustration
      *1 Protective Tape

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  13. REMOVE NO. 4 AIR DUCT SUB-ASSEMBLY


    1. A01NLMV

      Disengage the claw and guide, and remove the No. 4 air duct sub-assembly.

      Note

      Do not damage the claw or guide.

  14. REMOVE STOP LIGHT SWITCH ASSEMBLY


    1. A01NJZF

      Disconnect the connector.

    2. A01NLZHE01
      Text in Illustration
      *1 Lock Nut

      Loosen the stop light switch lock nut and remove the stop light switch assembly.

  15. REMOVE BRAKE PEDAL STROKE SENSOR ASSEMBLY


    1. A01NN7Q

      Disconnect the connector from the brake pedal stroke sensor assembly.

    2. A01NJOQ

      Remove the 2 bolts and brake pedal stroke sensor assembly from the brake pedal support assembly.

      Note


      • Do not drop the brake pedal stroke sensor assembly.

      • If the brake pedal stroke sensor assembly has been dropped, replace it with a new one.

  16. REMOVE BRAKE PEDAL RETURN SPRING


    1. A01NMZY

      Remove the brake pedal return spring from the push rod pin and brake pedal support sub-assembly.

  17. SEPARATE MASTER CYLINDER PUSH ROD CLEVIS


    1. A01NMRX

      Remove the clip and push rod pin, and separate the master cylinder push rod clevis from the brake pedal sub-assembly.

  18. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY


    1. A01NK5W

      Remove the 2 bolts and separate the brake pedal support assembly from the instrument panel reinforcement.

    2. A01NKWD

      Disengage the clamp.

    3. A01NMZL

      Remove the 4 nuts and brake pedal support assembly from the body.