BACK DOOR OUTSIDE GARNISH INSTALLATION


  1. INSTALL BACK DOOR OUTSIDE GARNISH PROTECTOR


    1. Wipe off any tape adhesive residue with cleaner.

    2. Coat the installation surface on the back door outside garnish with primer.

    3. Remove the release paper from a new back door outside garnish protector.

      Tech Tips

      After removing the release paper, keep the exposed adhesive free from foreign matter.

    4. A019KQ9

      Install a new back door outside garnish protector to the back door outside garnish as shown in the illustration.

  2. INSTALL BACK DOOR GARNISH SIDE PROTECTOR LH


    1. Wipe off any tape adhesive residue with cleaner.

    2. Remove the release paper from a new back door outside garnish protector.

      Tech Tips

      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. A019KWX

      Install a new back door garnish side protector LH to the back door outside garnish as shown in the illustration.

  3. INSTALL BACK DOOR GARNISH SIDE PROTECTOR RH

    Tech Tips

    Use the same procedure as for the LH side.

  4. INSTALL BACK DOOR OPENER SWITCH ASSEMBLY


    1. A019N7V

      Install the back door opener switch assembly.

  5. INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY


    1. Install 2 bolts.

    2. Install 2 stud bolts.

    3. Install 2 new back door outside garnish clips and 4 new gaskets on the back door outside garnish subassembly.

    4. A019KA8

      Engage the 2 clips to install the back door outside garnish sub-assembly.

    5. Install the 4 nuts.

      Torque:
      4.9 N*m  { 50 kgf*cm, 43 in.*lbf }

    6. Connect each connector.

  6. INSTALL BACK DOOR TRIM PANEL ASSEMBLY


    1. A019LDRE01
      Text in Illustration
      *1 2-piece Type Clip

      Engage the 2 claws and 16 clips to install the back door trim panel assembly.

    2. Install the 2 screws.

  7. INSTALL BACK DOOR SERVICE HOLE COVER LH


    1. A019NI2

      Engage the 5 claws to install the back door service hole cover LH.

  8. INSTALL BACK DOOR SERVICE HOLE COVER RH


    1. A019P9A

      Engage the 5 claws to install the back door service hole cover RH.

  9. INSTALL BACK DOOR UPPER TRIM COVER LH


    1. A019NIZ

      Engage the 2 claws to install the back door upper trim cover LH.

  10. INSTALL BACK DOOR UPPER TRIM COVER RH


    1. A019L37

      Engage the 2 claws to install the back door upper trim cover RH.

  11. INSTALL NO. 2 ROOM LIGHT ASSEMBLY


    1. Connect the connector.

    2. A019KWD

      Engage the claw to install the No. 2 room light assembly.

  12. INSTALL BACK DOOR LOCK COVER


    1. A019M2K

      Engage the 4 claws to install the back door lock cover.

  13. INSTALL BACK DOOR FINISH COVER LH (w/o Power Back Door)


    1. A019OK7

      Engage the 6 claws to install the back door finish cover LH.

  14. INSTALL BACK DOOR TRIM BASE (w/ Power Back Door)


    1. A019N4R

      Engage the 4 claws to install the back door trim base.

  15. INSTALL BACK DOOR FINISH COVER RH (w/o Power Back Door)


    1. A019O6R

      Engage the 6 claws to install the back door finish cover RH.

  16. INSTALL DOOR PULL HANDLE WITH SWITCH (w/ Power Back Door)


    1. Connect the connector.

    2. A019LWL

      Engage the 6 claws to install the door pull handle with switch.

  17. INSTALL TONNEAU COVER SUB-ASSEMBLY