REAR DOOR WINDOW FRAME MOULDING REMOVAL


  1. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the engine switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A019NQT

      Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.

  4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. A019MYE

      Using a moulding remover, disengage the 2 clips and 3 claws.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  5. REMOVE REAR DOOR ARMREST COVER


    1. A019P2I

      Remove the rear door armrest cover.

  6. REMOVE COURTESY LIGHT ASSEMBLY


    1. A019K32E02
      Text in Illustration
      *A for LH Side
      *B for RH Side
      *1 Protective Tape

      Using a screwdriver wrapped with protective tape, disengage the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A019M5IE01

      Remove the 3 screws.

    2. Using a clip remover, disengage the 7 clips and 2 rear door trim board retainers.

      Text in Illustration
      *1 Rear Door Trim Board Retainer
    3. A019KBR

      Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

    4. Raise the rear door trim board sub-assembly to disengage the 4 claws and remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.

    5. for 12 Speakers or 15 Speakers:


      1. Disconnect the connector.

    6. A019KYK

      Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.

    7. Remove the 2 rear door trim board retainers (green) from the rear door trim board sub-assembly.

  8. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    1. A019PL3

      Using a moulding remover, disengage the 4 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.

  9. REMOVE REAR DOOR FRAME GARNISH


    1. A019N65

      Remove the 2 clips.

    2. Disengage the clip and remove the rear door frame garnish.

  10. REMOVE REAR DOOR TRIM BRACKET


    1. A019K4I

      Remove the 2 screws and rear door trim bracket.

  11. REMOVE REAR DOOR SERVICE HOLE COVER


    1. A019MOX

      Disconnect the 2 connectors and remove the rear door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  12. DISCONNECT REAR DOOR WEATHERSTRIP


    1. A019P6I

      Using a clip remover, disengage the clip and remove the upper part of the rear door weatherstrip to the extent that allows removal of the rear door window frame moulding.

  13. REMOVE REAR DOOR GLASS RUN


    1. A019NL0

      Remove the rear door glass run.

  14. REMOVE REAR DOOR VENT SEAL


    1. A019OUF

      Remove the rear door vent seal.

  15. REMOVE REAR DOOR WINDOW REAR GUIDE SUB-ASSEMBLY


    1. A019OVUE01
      Text in Illustration
      *1 Temporary Screw

      Loosen the temporary screw.

    2. Remove the bolt and screw.

    3. Disengage the claw, guide and remove the rear door window rear guide sub-assembly.

    4. Remove the temporary screw from the rear door window rear guide sub-assembly.

  16. REMOVE REAR DOOR REAR GUIDE SEAL


    1. A019ORO

      Remove the 2 screws and rear door rear guide seal.

  17. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. Connect the cable to the negative (-) battery terminal and the rear power window regulator motor connector.

    2. Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.


      1. w/ Navigation System for HDD:

        Note

        After the engine switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

        Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
        Specification Waiting Time
        w/o Telematics transceiver 60 sec.
        w/ Telematics transceiver 120 sec.

    3. Disconnect the power window regulator switch assembly and rear power window regulator motor connector.

    4. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait for 90 seconds after disconnecting the terminal to prevent the airbag from deploying Click here.

    5. A019NTX

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the door glass to fall.

    6. A019K1EE01

      Remove the rear door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

      Note

      Do not damage the door glass.

  18. REMOVE REAR DOOR BELT MOULDING ASSEMBLY


    1. A019MXUE01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the rear door belt moulding assembly.

    2. A019M3S

      Using a screwdriver, disengage the 5 claws and remove the rear door belt moulding assembly.

  19. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING SUB-ASSEMBLY

    Tech Tips

    When removing the rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding sub-assembly using a heat light.

    Heating Temperature
    Item Temperature
    Vehicle Body 40 to 60°C (104 to 140°F)
    Moulding 20 to 30°C (68 to 86°F)

    Note

    Do not heat the vehicle body or moulding excessively.


    1. Using a heat light, heat the rear door front window frame moulding sub-assembly.

    2. A019NCME01
      Text in Illustration
      *1 Double-sided Tape
      *2 Caulking Sponge

      Using a moulding remover, disengage the clip and remove the rear door front window frame moulding sub-assembly.

  20. REMOVE REAR DOOR REAR WINDOW FRAME MOULDING


    1. Insert a 4.0 mm (0.157 in.) drill bit into a drill.

    2. A019L4TE01
      Text in Illustration
      *1 Caulking Sponge

      Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

      Area Dimension
      A 5.0 mm (0.197 in.)

      Note

      Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    3. Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 3 rivets.

      Note


      • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

      • Prying the rivets with the drill may damage the rivet installation holes or drill bit.

      • Be careful of the drilled rivets, as they may be hot.

    4. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

    5. Disengage the guide and remove the rear door rear window frame moulding from the door frame.

  21. REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING


    1. Insert a 4.0 mm (0.157 in.) drill bit into a drill.

    2. A019MS7E01

      Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

      Area Dimension
      A 5.0 mm (0.197 in.)

      Note

      Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    3. Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 4 rivets.

      Note


      • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

      • Prying the rivets with the drill may damage the rivet installation holes or drill bit.

      • Be careful of the drilled rivets, as they may be hot.

    4. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

    5. Disengage the guide and remove the rear door upper window frame moulding from the door frame.