REAR DOOR BELT MOULDING REMOVAL

REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

1. 

   Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.

REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

1. 

   Using a moulding remover, disengage the 2 clips and 3 claws.

2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

REMOVE REAR DOOR ARMREST COVER

1. 

   Remove the rear door armrest cover.

REMOVE COURTESY LIGHT ASSEMBLY

1. 

   Using a screwdriver wrapped with protective tape, disengage the claw.

   Table 2. Text in Illustration

   *A	for LH Side
   *B	for RH Side
   *1	Protective Tape

2. Disconnect the connector and remove the courtesy light assembly.

REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

1. 

   Remove the 3 screws.

2. Using a clip remover, disengage the 7 clips and 2 rear door trim board retainers.

   Table 3. Text in Illustration

   *1	Rear Door Trim Board Retainer

3. 

   Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

4. Raise the rear door trim board sub-assembly to disengage the 4 claws and remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.

5. for 12 Speakers or 15 Speakers:

   
   

   1. Disconnect the connector.

6. 

   Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.

7. Remove the 2 rear door trim board retainers (green) from the rear door trim board sub-assembly.

REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

1. 

   Using a moulding remover, disengage the 4 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.

REMOVE REAR DOOR FRAME GARNISH

1. 

   Remove the 2 clips.

2. Disengage the clip and remove the rear door frame garnish.

REMOVE REAR DOOR TRIM BRACKET

1. 

   Remove the 2 screws and rear door trim bracket.

REMOVE REAR DOOR SERVICE HOLE COVER

1. 

   Disconnect the 2 connectors and remove the rear door service hole cover.

   Tip:

   Remove any remaining butyl tape from the door.

REMOVE REAR DOOR GLASS RUN

1. 

   Remove the rear door glass run.

REMOVE REAR DOOR VENT SEAL

1. 

   Remove the rear door vent seal.

REMOVE REAR DOOR WINDOW REAR GUIDE SUB-ASSEMBLY

1. 

   Loosen the temporary screw.

   Table 4. Text in Illustration

   *1	Temporary Screw

2. Remove the bolt and screw.

3. Disengage the claw, guide and remove the rear door window rear guide sub-assembly.

4. Remove the temporary screw from the rear door window rear guide sub-assembly.

REMOVE REAR DOOR REAR GUIDE SEAL

1. 

   Remove the 2 screws and rear door rear guide seal.

REMOVE REAR DOOR GLASS SUB-ASSEMBLY

1. Connect the cable to the negative (-) battery terminal and the rear power window regulator motor connector.

2. Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.

   
   

   1. w/ Navigation System for HDD:

      Note:

      After the engine switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

      Table 5. Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal

      Specification	Waiting Time
      w/o Telematics transceiver	60 sec.
      w/ Telematics transceiver	120 sec.

3. Disconnect the power window regulator switch assembly and rear power window regulator motor connector.

4. Disconnect the cable from the negative (-) battery terminal.

   CAUTION:

   Wait for 90 seconds after disconnecting the terminal to prevent the airbag from deploying (Click here).

5. 

   Remove the 2 bolts.

   Note:

   After the bolts are removed, do not allow the door glass to fall.

6. 

   Remove the rear door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

   Note:

   Do not damage the door glass.