FRONT DOOR BELT MOULDING REMOVAL


  1. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the engine switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A019LBW

      Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.

  4. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A019MQ1

      Using a moulding remover, disengage the 2 clips and 5 claws as shown in the illustration.

    2. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.

  5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. A019O4F

      Using a moulding remover, disengage the 2 clips and 5 claws.

    2. Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.

  6. REMOVE DOOR ARMREST COVER


    1. A019NO5

      Remove the door armrest cover.

  7. REMOVE COURTESY LIGHT ASSEMBLY


    1. A019NF7E02
      Text in Illustration
      *A for LH Side
      *B for RH Side
      *1 Protective Tape

      Using a screwdriver wrapped with protective tape, disengage the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  8. REMOVE NO. 1 FRONT DOOR STIFFENER CUSHION


    1. A019M7L

      Remove the screw and No. 1 front door stiffener cushion.

  9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A019M4HE02

      Remove the 3 screws.

    2. Using a clip remover, disengage the 10 clips and front door trim board retainer.

      Text in Illustration
      *1 Front Door Trim Board Retainer
    3. A019L95

      Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

    4. Raise the front door trim board sub-assembly to disengage the 4 claws and remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.

    5. Disconnect each connector.

    6. A019LDJ

      Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.

    7. Remove the front door trim board retainer (green) from the front door trim board sub-assembly.

  10. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    1. A019MNY

      Using a moulding remover, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.

  11. REMOVE DOOR FRAME GARNISH


    1. A019KMZ

      Remove the 2 clips and door frame garnish.

  12. REMOVE FRONT NO. 3 SPEAKER ASSEMBLY


    1. A019LAN

      Disconnect the connector.

    2. Remove the 2 screws.

    3. Disengage the clip and remove the front No. 3 speaker assembly.

  13. REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY


    1. A019K78

      Disconnect each connector.

    2. Remove the 2 screws and the outer mirror control ECU assembly.

  14. REMOVE NO. 1 FRONT DOOR TRIM BRACKET


    1. A019PA1

      Remove the 2 screws and No. 1 front door trim bracket.

  15. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. A019O7G

      Disconnect the connector.

    2. Remove the front door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  16. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    1. Connect the cable to the negative (-) battery terminal.

    2. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


      1. w/ Navigation System for HDD:

        Note

        After the engine switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

        Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
        Specification Waiting Time
        w/o Telematics transceiver 60 sec.
        w/ Telematics transceiver 120 sec.

    3. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system Click here.

    4. A019KOB

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the door glass to fall.

    5. A019KQHE01

      Remove the front door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

      Note

      Do not damage the door glass.

  17. REMOVE FRONT DOOR GLASS RUN


    1. A019ODG

      Remove the front door glass run.

  18. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY


    1. A019OGJE01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the front door belt moulding assembly.

    2. A019LUY

      Using a screwdriver, disengage the 6 claws and remove the front door belt moulding assembly.