LIGHTING SYSTEM OPERATION CHECK


  1. AUTOMATIC LIGHT CONTROL SYSTEM OPERATION CHECK


    1. Turn the engine switch on (IG).

    2. Turn the light control switch to the AUTO position.

    3. Cover the automatic light control sensor.

    4. Check that the taillights and low beam headlights come on.

    5. Uncover the automatic light control sensor.

    6. Check that the low beam headlights and taillights go off.

  2. LIGHT AUTO TURN-OFF SYSTEM OPERATION CHECK (except European Models)


    1. Close all doors.

    2. Turn the engine switch on (IG).

    3. Turn the taillights, low beam headlights, high beam headlights, front fog lights and rear fog lights on.

    4. Turn the engine switch off.

    5. Open the driver door.

    6. Check that all of lights go off.

  3. LIGHT AUTO TURN-OFF SYSTEM OPERATION CHECK (for European Models)


    1. When light control switch in tail or head position


      1. Turn the engine switch on (IG).

      2. Turn the low beam headlights, high beam headlights, or front fog lights on.

      3. Turn the engine switch off.

      4. Check that the low beam headlights, high beam headlights and front fog lights go off immediately.

        Tech Tips

        Taillights and rear fog lights remain on.

    2. When light control switch in AUTO position


      1. Turn the engine switch on (IG).

      2. Turn the taillights, low beam headlights, high beam headlights, front fog lights or rear fog lights on.

      3. Turn the engine switch off.

      4. Check that all of lights go off immediately.

  4. DAYTIME RUNNING LIGHT SYSTEM OPERATION CHECK


    1. Turn the light control switch off.

    2. Start the engine.

    3. Check that the daytime running lights come on.

  5. HID HEADLIGHT SYSTEM OPERATION CHECK


    1. Perform the following diagnosis procedure when both of the following conditions are met: 1) the light control ECU is not visibly damaged, and 2) the light control ECU has been struck but is operating normally. If all of the following diagnosis results are normal, the light control ECU can be reused.


      1. Perform low beam headlight cold starts (10 minutes or more off, then turned on) and hot starts (15 minutes or more on, 1 minute off, then turned on again) several times. Check that the low beam headlights illuminate normally.

      2. For 5 minutes immediately after the lights are started cold (before the lights stabilize), visually check the illumination condition and check that the lights do not flicker or show signs of instability.

      3. Install bulbs that have approximately the same usage time, and illuminate the low beam headlights for approximately 30 seconds. Check that the brightness of the left and right bulbs are approximately the same, and that the illumination is stable.

  6. AFS OPERATION CHECK


    1. Check that the initialization (determination of the initial position) of the swivel motor is performed after the engine is started.

    2. A019L11

      Check that the AFS OFF indicator light in the combination meter assembly comes on for approximately 3 seconds and then goes off when the engine switch is turned on (IG).

  7. DOOR MIRROR FOOT LIGHT SYSTEM OPERATION CHECK


    1. The operation and condition of this control are described below.

      Operation Condition
      Illuminate for 15 seconds, and then fade out

      When any of the following conditions is met, the lights illuminate for 15 seconds, and then fade out:


      • The key enters any actuation area around the doors when the engine switch is off and all doors are closed*1.

      • Any door is unlocked when the engine switch is off, all doors are closed and locked.

      • Either driver door control switch or front passenger door control switch is turned to unlock position when engine switch is on (IG) and shift lever is in P.
      Fade out immediately

      When any of the following conditions is met, the lights fade out immediately:


      • The engine switch is turned from off to on (ACC) when all doors are closed.

      • All doors are locked when the engine switch is off, all doors are closed and any door is unlocked.

      • All doors are locked again when all doors are closed and locked.

      • The shift lever is moved to any position other than P when the engine switch is on (IG).

      Tech Tips

      *1: When the lights are on, if the key leaves the actuation areas around the doors, after approximately 3 seconds, the lights fade out.

  8. WELCOME LIGHTING SYSTEM OPERATION CHECK


    1. Turn the light control switch to the AUTO position.

    2. Cover the automatic light control sensor.

    3. Turn the engine switch off.

    4. Close and lock all doors.

    5. Unlock all doors by wireless door unlock or entry door unlock.

    6. Check that the parking lights come on for approximately 15 seconds.

  9. FOLLOW ME HOME SYSTEM OPERATION CHECK


    1. Turn the engine switch off.

    2. Turn the light control switch to the off or AUTO position.

    3. Pull the light control switch to flash headlights once.

    4. Check that the low beam headlights come on for approximately 30 seconds.