CENTER AIRBAG SENSOR ASSEMBLY INSTALLATION


  1. INSTALL CENTER AIRBAG SENSOR ASSEMBLY


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A019OZTE02
      Text in Illustration
      *1 Fulcrum Length
      *2 Waterproof Sheet

      Using SST and a torque wrench, install the center airbag sensor assembly with the 3 bolts.

      SST
      09961-00950
      Torque:
      without SST
      18 N*m  { 178 kgf*cm, 13 ft.*lbf }
      with SST
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

      Note


      • Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).

      • This torque value is effective when SST is parallel to a torque wrench.

      • If the center airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

      • When installing the center airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

      • When the engine switch is first turned on (IG) after the center airbag sensor assembly has been replaced, make sure that no one is in the vehicle.

    4. Connect the connector to the center airbag sensor assembly as shown in the illustration.

      Note

      When connecting the airbag connector, take care not to damage the airbag wire harness.

    5. Check that the waterproof sheet is properly set.

    6. Check that there is no looseness in the installation parts of the center airbag sensor assembly.

  2. INSTALL CONSOLE BOX (for LHD)


    1. A019MGBE01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Engage the 3 guides as shown in the illustration.

    2. Engage the 2 clamps.

    3. Install the 3 clips.

    4. Install the console box with the 5 screws <D>.

  3. INSTALL CONSOLE BOX (for RHD)


    1. A019MQ4E01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Engage the 3 guides as shown in the illustration.

    2. Engage the 2 clamps.

    3. Install the 2 clips.

    4. Install the console box with the 5 screws <D>.

  4. INSTALL FRONT CONSOLE BOX COVER


    1. A019M0N

      Connect the connector.

    2. Engage the 5 guides and 2 clips, and install the front console box cover.

  5. INSTALL REAR CONSOLE BOX ASSEMBLY


    1. A019JU4E01

      Engage the 8 guides as shown in the illustration.

      Note

      Make sure to install the rear console box assembly in the direction indicated by the arrow (1). Failure to do so will damage the console box and front seat.

    2. Install the rear console box assembly with the 2 screws and 4 bolts.

  6. INSTALL CONSOLE REAR END PANEL SUB-ASSEMBLY


    1. w/o Rear Seat Entertainment System:


      1. Engage the 5 claws and 6 clips to install the console rear end panel sub-assembly.

    2. w/ Rear Seat Entertainment System:


      1. Connect each connector.

      2. Engage the 5 claws and 6 clips to install the console rear end panel sub-assembly.

  7. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL


    1. A019KVZ

      Engage the 7 clips to install the lower instrument panel finish panel as shown in the illustration.

  8. INSTALL INSTRUMENT PANEL FINISH PANEL


    1. A019MX7

      Engage the 2 guides, claw and 2 clips to install the instrument panel finish panel as shown in the illustration.

  9. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. Connect each connector.

    2. Engage the 8 clips and 2 guides.

    3. Install the lower instrument panel finish panel sub-assembly with the 2 screws <D>.

    4. A019NKJ

      Engage the 2 claws to close the cover as shown in the illustration.

  10. INSTALL NO. 1 SWITCH HOLE BASE


    1. Connect each connector.

    2. A019N7C

      Engage the 4 claws and 2 guides to install the No. 1 switch hole base.

  11. INSTALL INSTRUMENT PANEL GARNISH LH


    1. A019K28

      Engage the 6 clips to install the instrument panel garnish LH.

  12. INSTALL NO. 2 CONSOLE BOX DUCT


    1. Install the No. 2 console box duct with the 2 screws.

    2. Connect each connector and engage the 2 clamps.

  13. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. Engage the clamp.

    2. Connect each connector.

    3. A019MFZ

      Engage the 3 claws and 3 clips.

    4. w/o Seat Heater System:


      1. Connect the connector to the console box hole cover.

    5. w/ Seat Heater System:


      1. Connect the connector.

      2. Engage the 6 claws to install the seat heater switch with console box hole cover.

    6. A019LES

      Engage the 4 claws and 4 clips to install the upper console panel sub-assembly.

  14. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A019LZO

      Turn the shift lever knob sub-assembly clockwise to install the shift lever knob sub-assembly.

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  16. DIAGNOSTIC SYSTEM CHECK


    1. Perform a diagnostic system check Click here.

  17. INSTALL SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.

  18. INSPECT SUSPENSION CONTROL SYSTEM (w/ Air Suspension)


    1. Inspect the suspension control system Click here.