CENTER AIRBAG SENSOR ASSEMBLY REMOVAL


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

    Note

    w/ Navigation System for HDD:

    After the engine switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
    Specification Waiting Time
    w/o Telematics transceiver 60 sec.
    w/ Telematics transceiver 120 sec.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A019LPB

      Turn the shift lever knob sub-assembly counterclockwise and remove the shift lever knob sub-assembly.

  4. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A019OY8

      Move the shift lever to N.

    2. Pull the upper console panel sub-assembly in the direction indicated by the arrow to disengage the 4 claws and 4 clips.

    3. w/o Seat Heater System:


      1. Disconnect the connector from the console box hole cover.

    4. w/ Seat Heater System:


      1. A019OCZ

        Disengage the 6 claws.

      2. Disconnect the connector and remove the seat heater switch with console box hole cover.

    5. A019K0Q

      Pull the upper console panel sub-assembly in the direction indicated by the arrow to disengage the 3 claws and 3 clips.

    6. Disconnect each connector.

    7. Disengage the clamp and remove the upper console panel sub-assembly.

  5. REMOVE NO. 2 CONSOLE BOX DUCT


    1. A019N18

      Disconnect each connector and disengage the 2 clamps.

    2. A019KD8

      Remove the 2 screws and the No. 2 console box duct.

  6. REMOVE INSTRUMENT PANEL GARNISH LH


    1. A019MAJ

      Using moulding remover B, disengage the 6 clips and remove the instrument panel garnish LH as shown in the illustration.

  7. REMOVE NO. 1 SWITCH HOLE BASE


    1. A019JWR

      Push the No. 1 switch hole base in the direction indicated by the arrow to disengage the 4 claws and 2 guides.

    2. Disconnect each connector and remove the No. 1 switch hole base.

  8. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A019N7Y

      Disengage the 2 claws and open the cover as shown in the illustration.

    2. A019KVT

      Remove the 2 screws <D>.

    3. Disengage the 8 clips and 2 guides.

    4. Disconnect each connector and remove the lower instrument panel finish panel sub-assembly.

  9. REMOVE INSTRUMENT PANEL FINISH PANEL


    1. A019PC7

      Pull the instrument panel finish panel in the direction indicated by the arrow to disengage the claw, 2 clips and 2 guides, and remove the instrument panel finish panel.

  10. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL


    1. A019MQD

      Pull the lower instrument panel finish panel in the direction indicated by the arrow to disengage the 7 clips and remove the lower instrument panel finish panel.

  11. REMOVE CONSOLE REAR END PANEL SUB-ASSEMBLY


    1. A019OL2

      w/o Rear Seat Entertainment System:


      1. Disengage the 5 claws and 6 clips, and remove the console rear end panel sub-assembly.

    2. w/ Rear Seat Entertainment System:


      1. Disengage the 5 claws and 6 clips.

      2. Disconnect each connector and remove the console rear end panel sub-assembly.

  12. REMOVE REAR CONSOLE BOX ASSEMBLY


    1. A019LRAE01
      Text in Illustration
      *1 Screw
      *2 Bolt

      Remove the 2 screws and 4 bolts.

    2. A019PIBE01

      Pull the rear console box assembly in the direction indicated by the arrow (1) to disengage the 8 guides and remove the rear console box assembly as shown in the illustration.

      Note

      Make sure to remove the rear console box assembly in the direction indicated by the arrow (2). Failure to do so will damage the console box and front seat.

  13. REMOVE FRONT CONSOLE BOX COVER


    1. A019P7H

      Using moulding remover A, disengage the 2 clips and 5 guides.

    2. Disconnect the connector and remove the front console box cover.

  14. REMOVE CONSOLE BOX (for LHD)


    1. A019KOZ

      Remove the 5 screws <D>.

    2. A019OKHE01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Disengage the 2 clamps.

    3. Remove the 3 clips.

    4. Disengage the 3 guides and remove the console box as shown in the illustration.

  15. REMOVE CONSOLE BOX (for RHD)


    1. A019NGF

      Remove the 5 screws <D>.

    2. A019KN6E01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Disengage the 2 clamps.

    3. Remove the 2 clips.

    4. Disengage the 3 guides and remove the console box as shown in the illustration.

  16. REMOVE CENTER AIRBAG SENSOR ASSEMBLY


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A019N1O

      Disconnect the connector from the center airbag sensor assembly as shown in the illustration.

      Note

      When disconnecting the airbag connector, take care not to damage the airbag wire harness.

    4. Remove the 3 bolts and center airbag sensor assembly.