SPIRAL CABLE INSTALLATION


  1. INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note


    • Do not replace the spiral cable with the battery connected and the engine switch on (IG).

    • Do not rotate the spiral cable with the battery connected and the engine switch on (IG).

    • Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.

    • Do not remove the steering sensor from the spiral cable.


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

    3. Check that the front wheels are facing straight ahead.

    4. Set the turn signal switch to the neutral position.

      Note

      If it is not in the neutral position, the turn signal switch pin may snap.

    5. A019OH0

      Install the spiral cable with sensor sub-assembly with the 3 claws.

      Note

      When replacing the spiral cable with sensor sub-assembly with a new one, remove the lock pin before installing the steering wheel assembly.

    6. Connect the connectors to the spiral cable with sensor sub-assembly.

      Note

      When connecting the airbag connector, take care not to damage the airbag wire harness.

  2. INSTALL STEERING COLUMN COVER


    1. A019KOA

      Engage the claw to install the upper steering column cover.

    2. A019MWZ

      Engage the 2 claws to install the lower steering column cover to the upper steering column cover.

      Note

      Do not damage the tilt and telescopic switch.

    3. Install the 3 screws.

      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }
    4. A019KKPE01
      Text in Illustration
      *1 Instrument Panel Cluster Finish Panel

      Engage the 4 clips and 2 guides to install the instrument panel cluster finish panel to the upper steering column cover.

  3. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  4. ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A019M35

      Rotate the spiral cable counterclockwise slowly by hand until it stops.

      Note

      Do not turn the spiral cable using the airbag wire harness.

    4. A019MARE02
      Text in Illustration
      *A w/o Steering Heater
      *B w/ Steering Heater
      *a Alignment Mark

      Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

      Note

      Do not turn the spiral cable using the airbag wire harness.

      Tech Tips

      The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.

  5. INSTALL STEERING WHEEL ASSEMBLY


    1. A019NOBE01
      Text in Illustration
      *a Matchmark

      Install the steering wheel assembly aligning the matchmarks on the steering wheel assembly and steering main shaft.

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

    3. w/ Steering Heater:


      1. Connect the connector.

    4. Connect each connector to the spiral cable.

  6. INSPECT STEERING WHEEL CENTER POINT

  7. INSTALL STEERING PAD


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A019N0Z

      Connect the 2 airbag connectors to the steering pad.

      Note


      • When connecting any airbag connector, take care not to damage the airbag wire harness.

      • Be sure to only connect the connectors to each corresponding color.

    4. Push in the 2 airbag connector locks to install the 2 airbag connectors.

    5. Connect the horn connector to the steering pad.

    6. A019KX4

      Push the steering pad to attach the 3 pins carefully.

      Note


      • Make sure that the pins are securely inserted into the steering holes.

      • Make sure to engage the 2 upper pins first.

      • Make sure that the steering pad is securely installed.

  8. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    1. Engage the claw to install the lower No. 3 steering wheel cover.

  9. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    1. Engage the claw to install the lower No. 2 steering wheel cover.

  10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note


    • Make sure that the cable has been disconnected from the battery terminal for at least 2 seconds before reconnecting the cable.

    • Connect the cable to the negative (-) battery terminal with the front wheels facing straight ahead.

    • Reset the auto tilt away function setting to the previous condition by changing the customize parameter Click here.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  11. INSPECT STEERING PAD


    1. Make sure that the horn sounds.

      Tech Tips

      If the horn does not sound, inspect the horn system Click here.

  12. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  13. INSPECT SRS WARNING LIGHT

    Click here