AIRBAG SYSTEM, Diagnostic DTC:B1627/82, B1628/82, B1637/82, B1638/82, B1647/82

DTC Code DTC Name
B1627/82 Lost communication with Side Airbag Sensor LH
B1628/82 Side Airbag Sensor Assembly LH Initialization Incomplete
B1637/82 Lost Communication with Rear Airbag Sensor LH
B1638/82 Rear Airbag Sensor Assembly LH Initialization Incomplete
B1647/82 Lost Communication with Side Satellite Sensor Bus LH

DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH) is composed of the center airbag sensor assembly, side airbag sensor LH, and rear airbag sensor LH.

The side airbag sensor LH and rear airbag sensor LH detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbag should be deployed.

These DTCs are recorded when a malfunction is detected for the side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).

DTC No. DTC Detection Condition Trouble Area

B1627/82

B1628/82

B1637/82

B1638/82

B1647/82

  • The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).

  • Side airbag sensor LH malfunction

  • Rear airbag sensor LH malfunction

  • Center airbag sensor assembly malfunction

  • No. 2 floor wire

  • Side airbag sensor LH

  • Rear airbag sensor LH

  • Center airbag sensor assembly

WIRING DIAGRAM

A019LWGE06

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK PRESENT DTC


    1. Turn the engine switch on (IG), and wait for at least 60 seconds.

    2. Check for present DTCs Click here.

      Result
      Result Proceed to
      Present DTC B1647 or 82 is output. A
      Present DTC B1628 is output. B
      Present DTC B1637 or B1638 is output. C
      Present DTC B1627 is output. D
      Present DTCs B1627, B1628, B1637, B1638, B1647 and 82 are not output. E

      Tech Tips


      • DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the engine switch off and then on (IG) again.

      • Codes other than DTCs B1627, B1628, B1637, B1638, B1647 and 82 may be output at this time, but they are not related to this check.


    B

    CHECK PAST DTC Click here

    C

    CHECK CONNECTORS Click here

    D

    CHECK SIDE AIRBAG SENSOR LH Click here

    E

    USE SIMULATION METHOD TO CHECK Click here

    A

  2. CHECK CONNECTORS


    1. Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      Note

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the center airbag sensor assembly, side airbag sensor LH and rear airbag sensor LH.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the center airbag sensor assembly, side airbag sensor LH and rear airbag sensor LH.

    5. Check that the terminals of connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  3. CHECK NO. 2 FLOOR WIRE (OPEN)


    1. Using SST, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

      A019M8TE02
      Text in Illustration
      *1 Side Airbag Sensor LH *2 Center Airbag Sensor Assembly
      *3 No. 2 Floor Wire *4

      Front view of wire harness connector

      (to Center Airbag Sensor Assembly)
      *5

      Front view of wire harness connector

      (to Side Airbag Sensor LH)

      		 *6 Connector B
      *7 Connector C - -

      Note

      Do not forcibly insert SST into the terminals of the connector when connecting.

      SST
      09843-18040

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-4 (BBL+) - P4-3 (BBL-) Always Below 1 Ω

    3. Disconnect SST from connector B.


    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  4. CHECK NO. 2 FLOOR WIRE (SHORT)


    1. A019O24E03
      Text in Illustration
      *1 Side Airbag Sensor LH
      *2 Center Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector C

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-4 (BBL+) - P4-3 (BBL-) Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  5. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. A019O24E03
      Text in Illustration
      *1 Side Airbag Sensor LH
      *2 Center Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector C

      Connect the cable to the negative (-) battery terminal.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      P4-4 (BBL+) - Body ground Engine switch on (IG) Below 1 V
      P4-3 (BBL-) - Body ground Engine switch on (IG) Below 1 V

    4. Turn the engine switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      Note

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  6. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. A019O24E03
      Text in Illustration
      *1 Side Airbag Sensor LH
      *2 Center Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector C

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-4 (BBL+) - Body ground Always 1 MΩ or higher
      P4-3 (BBL-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  7. CHECK NO. 2 FLOOR WIRE (OPEN)


    1. Using SST, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

      A019P4JE07
      Text in Illustration
      *1 Rear Airbag Sensor LH *2 Side Airbag Sensor LH
      *3 No. 2 Floor Wire *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      		 *6 Connector B
      *7 Connector C - -

      Note

      Do not forcibly insert SST into the terminals of the connector when connecting.

      SST
      09843-18040

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-1 (BCL+) - P4-2 (BCL-) Always Below 1 Ω

    3. Disconnect SST from connector C.


    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  8. CHECK NO. 2 FLOOR WIRE (SHORT)


    1. A019KW7E04
      Text in Illustration
      *1 Rear Airbag Sensor LH
      *2 Side Airbag Sensor LH
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector B

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-1 (BCL+) - P4-2 (BCL-) Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  9. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. A019KW7E04
      Text in Illustration
      *1 Rear Airbag Sensor LH
      *2 Side Airbag Sensor LH
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector B

      Connect the cable to the negative (-) battery terminal.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      P4-1 (BCL+) - Body ground Engine switch on (IG) Below 1 V
      P4-2 (BCL-) - Body ground Engine switch on (IG) Below 1 V

    4. Turn the engine switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      Note

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  10. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. A019KW7E04
      Text in Illustration
      *1 Rear Airbag Sensor LH
      *2 Side Airbag Sensor LH
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector B

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-1 (BCL+) - Body ground Always 1 MΩ or higher
      P4-2 (BCL-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  11. CHECK SIDE AIRBAG SENSOR LH


    1. A019L4PE01
      Text in Illustration
      *1 Side Airbag Sensor RH
      *2 Center Airbag Sensor Assembly

      Connect the connectors to the rear airbag sensor LH and center airbag sensor assembly.

    2. Interchange the side airbag sensor LH with RH and connect the connectors.

    3. Connect the cable to the negative (-) battery terminal.

    4. Turn the engine switch on (IG), and wait for at least 60 seconds.

    5. Clear the DTCs stored in the memory Click here.

    6. Turn the engine switch off.

    7. Turn the engine switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1647 or 82 is output. A
      DTC B1642 or 81 is output. B
      DTCs B1642, B1647, 81 and 82 are not output. C

      Tech Tips

      Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.

    9. Turn the engine switch off.

    10. Disconnect the cable from the negative (-) battery terminal.

      Note

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    11. Return the side airbag sensor LH and RH to their original positions and connect the connectors.


    B

    REPLACE SIDE AIRBAG SENSOR LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  12. CHECK REAR AIRBAG SENSOR LH


    1. A019OPGE16
      Text in Illustration
      *1 Rear Airbag Sensor RH
      *2 Side Airbag Sensor LH

      Interchange the rear airbag sensor LH with RH and connect the connectors.

    2. Connect the cable to the negative (-) battery terminal.

    3. Turn the engine switch on (IG), and wait for at least 60 seconds.

    4. Clear the DTCs stored in the memory Click here.

    5. Turn the engine switch off.

    6. Turn the engine switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTCs B1642, B1647, 81 and 82 are not output. A
      DTC B1647 or 82 is output. B
      DTC B1642 or 81 is output. C

      Tech Tips

      Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.

    8. Turn the engine switch off.

    9. Disconnect the cable from the negative (-) battery terminal.

      Note

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    10. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.


    B

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

    C

    REPLACE REAR AIRBAG SENSOR LH Click here

    A

    USE SIMULATION METHOD TO CHECK Click here

  13. CHECK PAST DTC


    1. Turn the engine switch on (IG), and wait for at least 60 seconds.

    2. Check for past DTCs Click here.

      Result
      Result Proceed to
      Past DTC B1627 is not output. A
      Past DTC B1627 is output. B

      Tech Tips

      Codes other than past DTC B1627 may be output at this time, but they are not related to this check.


    B

    CHECK SIDE AIRBAG SENSOR LH Click here

    A

  14. CHECK CONNECTORS


    1. Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      Note

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the center airbag sensor assembly and side airbag sensor LH.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the center airbag sensor assembly and side airbag sensor LH.

    5. Check that the terminals of connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  15. CHECK NO. 2 FLOOR WIRE (OPEN)


    1. Using SST, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

      A019M8TE02
      Text in Illustration
      *1 Side Airbag Sensor LH *2 Center Airbag Sensor Assembly
      *3 No. 2 Floor Wire *4

      Front view of wire harness connector

      (to Center Airbag Sensor Assembly)
      *5

      Front view of wire harness connector

      (to Side Airbag Sensor LH)

      		 *6 Connector B
      *7 Connector C - -

      Note

      Do not forcibly insert SST into the terminals of the connector when connecting.

      SST
      09843-18040

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-4 (BBL+) - P4-3 (BBL-) Always Below 1 Ω

    3. Disconnect SST from connector B.


    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  16. CHECK NO. 2 FLOOR WIRE (SHORT)


    1. A019O24E03
      Text in Illustration
      *1 Side Airbag Sensor LH
      *2 Center Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector C

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-4 (BBL+) - P4-3 (BBL-) Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  17. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. A019O24E03
      Text in Illustration
      *1 Side Airbag Sensor LH
      *2 Center Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector C

      Connect the cable to the negative (-) battery terminal.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      P4-4 (BBL+) - Body ground Engine switch on (IG) Below 1 V
      P4-3 (BBL-) - Body ground Engine switch on (IG) Below 1 V

    4. Turn the engine switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      Note

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  18. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. A019O24E03
      Text in Illustration
      *1 Side Airbag Sensor LH
      *2 Center Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector C

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-4 (BBL+) - Body ground Always 1 MΩ or higher
      P4-3 (BBL-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  19. CHECK SIDE AIRBAG SENSOR LH


    1. A019L4PE01
      Text in Illustration
      *1 Side Airbag Sensor RH
      *2 Center Airbag Sensor Assembly

      Connect the connector to the center airbag sensor assembly.

    2. Interchange the side airbag sensor LH with RH and connect the connectors.

    3. Connect the cable to the negative (-) battery terminal.

    4. Turn the engine switch on (IG), and wait for at least 60 seconds.

    5. Clear the DTCs stored in the memory Click here.

    6. Turn the engine switch off.

    7. Turn the engine switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs Click here.

      Result
      Result Proceed to
      DTCs B1623 and B1628 are not output. A
      DTC B1628 is output. B
      DTC B1623 is output. C

      Tech Tips

      Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.

    9. Turn the engine switch off.

    10. Disconnect the cable from the negative (-) battery terminal.

      Note

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    11. Return the side airbag sensor LH and RH to their original positions and connect the connectors.


    B

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

    C

    REPLACE SIDE AIRBAG SENSOR LH Click here

    A

    USE SIMULATION METHOD TO CHECK Click here

  20. CHECK CONNECTORS


    1. Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      Note

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the side airbag sensor LH and rear airbag sensor LH.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.

    5. Check that the terminals of connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  21. CHECK NO. 2 FLOOR WIRE (OPEN)


    1. Using SST, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

      A019P4JE07
      Text in Illustration
      *1 Rear Airbag Sensor LH *2 Side Airbag Sensor LH
      *3 No. 2 Floor Wire *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      		 *6 Connector B
      *7 Connector C - -

      Note

      Do not forcibly insert SST into the terminals of the connector when connecting.

      SST
      09843-18040

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-1 (BCL+) - P4-2 (BCL-) Always Below 1 Ω

    3. Disconnect SST from connector C.


    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  22. CHECK NO. 2 FLOOR WIRE (SHORT)


    1. A019KW7E04
      Text in Illustration
      *1 Rear Airbag Sensor LH
      *2 Side Airbag Sensor LH
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector B

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-1 (BCL+) - P4-2 (BCL-) Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  23. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. A019KW7E04
      Text in Illustration
      *1 Rear Airbag Sensor LH
      *2 Side Airbag Sensor LH
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector B

      Connect the cable to the negative (-) battery terminal.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      P4-1 (BCL+) - Body ground Engine switch on (IG) Below 1 V
      P4-2 (BCL-) - Body ground Engine switch on (IG) Below 1 V

    4. Turn the engine switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      Note

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  24. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. A019KW7E04
      Text in Illustration
      *1 Rear Airbag Sensor LH
      *2 Side Airbag Sensor LH
      *3 No. 2 Floor Wire
      *4

      Front view of wire harness connector

      (to Side Airbag Sensor LH)
      *5 Connector B

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P4-1 (BCL+) - Body ground Always 1 MΩ or higher
      P4-2 (BCL-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  25. CHECK SIDE AIRBAG SENSOR LH


    1. A019L4PE01
      Text in Illustration
      *1 Side Airbag Sensor RH
      *2 Center Airbag Sensor Assembly

      Connect the connector to the rear airbag sensor LH.

    2. Interchange the side airbag sensor LH with RH and connect the connectors.

    3. Connect the cable to the negative (-) battery terminal.

    4. Turn the engine switch on (IG), and wait for at least 60 seconds.

    5. Clear the DTCs stored in the memory Click here.

    6. Turn the engine switch off.

    7. Turn the engine switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1637 or B1638 is output. A
      DTC B1632 or B1633 is output. B
      DTCs B1632, B1633, B1637 and B1638 are not output. C

      Tech Tips

      Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.

    9. Turn the engine switch off.

    10. Disconnect the cable from the negative (-) battery terminal.

      Note

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    11. Return the side airbag sensor LH and RH to their original positions and connect the connectors.


    B

    REPLACE SIDE AIRBAG SENSOR LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  26. CHECK REAR AIRBAG SENSOR LH


    1. A019OPGE16
      Text in Illustration
      *1 Rear Airbag Sensor RH
      *2 Side Airbag Sensor LH

      Interchange the rear airbag sensor LH with RH and connect the connectors.

    2. Connect the cable to the negative (-) battery terminal.

    3. Turn the engine switch on (IG), and wait for at least 60 seconds.

    4. Clear the DTCs stored in the memory Click here.

    5. Turn the engine switch off.

    6. Turn the engine switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTCs B1632, B1633, B1637 and B1638 are not output. A
      DTC B1637 or B1638 is output. B
      DTC B1632 or B1633 is output. C

      Tech Tips

      Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.

    8. Turn the engine switch off.

    9. Disconnect the cable from the negative (-) battery terminal.

      Note

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    10. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.


    B

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

    C

    REPLACE REAR AIRBAG SENSOR LH Click here

    A

    USE SIMULATION METHOD TO CHECK Click here

  27. CHECK SIDE AIRBAG SENSOR LH


    1. A019L4PE01
      Text in Illustration
      *1 Side Airbag Sensor RH
      *2 Center Airbag Sensor Assembly

      Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      Note

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Interchange the side airbag sensor LH with RH and connect the connectors.

    4. Connect the cable to the negative (-) battery terminal.

    5. Turn the engine switch on (IG), and wait for at least 60 seconds.

    6. Clear the DTCs stored in the memory Click here.

    7. Turn the engine switch off.

    8. Turn the engine switch on (IG), and wait for at least 60 seconds.

    9. Check for DTCs Click here.

      Result
      Result Proceed to
      DTCs B1622 and B1627 are not output. A
      DTC B1627 is output. B
      DTC B1622 is output. C

      Tech Tips

      Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.

    10. Turn the engine switch off.

    11. Disconnect the cable from the negative (-) battery terminal.

      Note

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    12. Return the side airbag sensor LH and RH to their original positions and connect the connectors.


    B

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

    C

    REPLACE SIDE AIRBAG SENSOR LH Click here

    A

    USE SIMULATION METHOD TO CHECK Click here