BACK DOOR COURTESY SWITCH REMOVAL


  1. REMOVE TONNEAU COVER SUB-ASSEMBLY

  2. REMOVE BACK DOOR FINISH COVER LH (w/o Power Back Door)


    1. A019LP5

      Using a moulding remover, disengage the 6 claws and remove the back door finish cover LH.

  3. REMOVE BACK DOOR TRIM BASE (w/ Power Back Door)


    1. A019NVD

      Using a moulding remover, disengage the 4 claws and remove the back door trim base.

  4. REMOVE BACK DOOR FINISH COVER RH (w/o Power Back Door)


    1. A019M26

      Using a moulding remover, disengage the 6 claws and remove the back door finish cover RH.

  5. REMOVE DOOR PULL HANDLE WITH SWITCH (w/ Power Back Door)


    1. A019NWD

      Using a moulding remover, disengage the 6 claws and remove the door pull handle with switch.

    2. Disconnect the connector.

  6. REMOVE BACK DOOR LOCK COVER


    1. A019M2K

      Disengage the 4 claws and remove the back door lock cover.

  7. REMOVE NO. 2 ROOM LIGHT ASSEMBLY


    1. A019PBLE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver wrapped with protective tape, disengage the claw.

    2. Disconnect the connector and remove the No. 2 room light assembly.

  8. REMOVE BACK DOOR UPPER TRIM COVER LH


    1. A019N57E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 2 claws and remove the back door upper trim cover LH as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

  9. REMOVE BACK DOOR UPPER TRIM COVER RH


    1. A019OM4E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 2 claws and remove the back door upper trim cover LH as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

  10. REMOVE BACK DOOR SERVICE HOLE COVER LH


    1. A019NI2

      Disengage the 5 claws and remove the back door service hole cover LH.

  11. REMOVE BACK DOOR SERVICE HOLE COVER RH


    1. A019P9A

      Disengage the 5 claws and remove the back door service hole cover RH.

  12. REMOVE BACK DOOR TRIM PANEL ASSEMBLY


    1. A019KQ7

      Remove the 2 screws.

    2. A019KECE01

      Grab the service holes by hand.

      Note

      Make sure to hold the clip bases as shown in the illustration.

    3. Pull the back door trim panel assembly in the direction shown by the arrows in the illustration (pull perpendicular to the surface of the trim panel) to disengage the 2 claws and 16 clips, and remove the back door trim panel assembly.

      Text in Illustration
      *1 2-piece Type Clip

      Note

      Removing the back door trim panel assembly at an angle may cause deformation or damage. To avoid this, make sure to pull the panel in the direction shown by the arrows (pull perpendicular to the surface of the panel).

      Tech Tips

      If any clips remain on the back door panel after the back door trim panel assembly is removed, remove the clips and install them to the back door trim panel assembly.

  13. REMOVE BACK DOOR LOCK ASSEMBLY (w/o Power Back Door)


    1. A019NVG

      Disconnect the connector.

    2. A019MIA

      Remove the 3 bolts and back door lock assembly.

  14. REMOVE BACK DOOR LOCK ASSEMBLY (w/ Power Back Door)


    1. A019JLU

      Disconnect the connector.

    2. Disengage the clamp.

    3. Remove the bolt.

    4. A019KLR

      Remove the 3 bolts and back door lock assembly.