Click here

ELECTRICAL KEY OSCILLATOR (for Center Floor) INSTALLATION

Click here
Click here Click here
  1. Click here

    INSTALL ELECTRICAL KEY OSCILLATOR


    1. Connect the connector.

    2. A019N6W

      Install the electrical key oscillator with the nut.

      Note:

      Be careful when installing the electrical key oscillator. If the oscillator is dropped, replace it with a new one.

    3. A019JU5

      Reinstall the floor carpet.

  2. Click here

    INSTALL REAR SEAT ASSEMBLY LH


    1. A019O6N

      Temporarily install the 2 bolts on the front side of the seat.

    2. A019PHD

      Temporarily install the 3 bolts on the rear side of the seat.

    3. w/ Rear Seat Side Airbag:


      1. A019MGI

        Connect the connector.

    4. Install the rear seat assembly LH with the 5 bolts.

      37 N*m 377 kgf*cm 27 ft.*lbf
  3. Click here

    CONNECT REAR SEAT LOCK CABLE ASSEMBLY LH


    1. When replacing the rear seat assembly LH or No. 2 rear seat reclining control cable with a new one:


      1. A019OJU

        Connect the rear seat assembly LH or No. 2 rear seat reclining control cable as shown in the illustration.

    2. When replacing the rear seat lock cable assembly LH with a new one:


      1. Engage the joint piece with the cable of the rear seat lock cable assembly LH.

      2. A019M5R

        Connect the rear seat lock cable assembly LH and connector case as shown in the illustration.

      3. A019NTP

        Push the lock pin of the connector case as shown in the illustration to connect the rear seat lock cable assembly LH.

    3. When reusing the rear seat assembly LH, No. 2 rear seat reclining control cable and rear seat lock cable assembly LH:


      1. A019P5T

        Connect the rear seat lock cable assembly LH as shown in the illustration.

      2. A019LV4E01

        Connect the No. 2 rear seat reclining control cable as shown in the illustration.

        Table 1. Text in Illustration
        *1 Seat Track Adjusting Handle *2 Protective Tape
      3. A019KQ4

        Install the rear seat reclining control cable to the cover as shown in the illustration.

      4. A019KZV

        Connect the No. 2 rear seat reclining control cable as shown in the illustration.

    4. Return the seatback to the upright position.

    5. A019ND0E01

      Press the adjusters lock piece to lock it as shown in the illustration.

      Table 2. Text in Illustration
      *1 Adjusters Spring *2 Lock Piece
      Note:

      When pressing the lock piece, make sure the adjusters spring is not compressed.

    6. A019KZY

      Engage the guide.

    7. Connect the No. 2 fold seat stopper band assembly with the bolt.

      9.0 N*m 92 kgf*cm 80 in.*lbf
    8. A019JQW

      Connect the rear seatback board carpet assembly with the 4 clips.

  4. Click here

    INSPECT REAR SEAT SLIDE ADJUSTER LOCK


    1. Check that the left and right adjusters lock simultaneously when sliding the seat.

    2. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.

  5. Click here

    INSTALL REAR SEAT TRACK BRACKET COVER LH


    1. A019P4B

      Engage the 8 claws and install the 2 rear seat track bracket cover LH.

  6. Click here

    INSTALL REAR SEAT HEADREST ASSEMBLY LH


    1. A019LT0

      Install the rear seat headrest assembly as shown in the illustration.

  7. Click here

    INSTALL REAR SEAT ASSEMBLY RH


    1. A019JSJ

      Temporarily install the 2 bolts on the front side of the seat.

    2. A019PE0

      Temporarily install the 3 bolts on the rear side of the seat.

    3. w/ Rear Seat Side Airbag:


      1. A019JTC

        Connect the connector.

    4. Install the rear seat assembly RH with the 5 bolts.

      37 N*m 377 kgf*cm 27 ft.*lbf
  8. Click here

    CONNECT REAR SEAT LOCK CABLE ASSEMBLY RH


    1. When replacing the rear seat assembly RH or rear seat reclining control cable with a new one:


      1. A019OJU

        Connect the rear seat assembly RH or rear seat reclining control cable as shown in the illustration.

    2. When replacing the rear seat lock cable assembly RH with a new one:


      1. Engage the joint piece with the cable of the rear seat lock cable assembly RH.

      2. A019M5R

        Connect the rear seat lock cable assembly RH and connector case as shown in the illustration.

      3. A019NTP

        Push the lock pin of the connector case as shown in the illustration to connect the rear seat lock cable assembly RH.

    3. When reusing the rear seat assembly RH, rear seat reclining control cable and rear seat lock cable assembly RH:


      1. A019JQ4

        Connect the rear seat lock cable assembly RH as shown in the illustration.

      2. A019NBDE01

        Connect the rear seat lock cable assembly RH as shown in the illustration.

        Table 3. Text in Illustration
        *1 Seat Track Adjusting *2 Protective Tape
      3. A019PDP

        Install the rear seat reclining control cable to the cover as shown in the illustration.

      4. A019LTO

        Connect the rear No. 1 seat lock cable assembly as shown in the illustration.

    4. Return the seatback to the upright position.

    5. A019K6OE01

      Press the adjuster's lock piece to lock it as shown in the illustration.

      Table 4. Text in Illustration
      *1 Adjusters Spring *2 Lock Piece
      Note:

      When pressing the lock piece, make sure the adjusters spring is not compressed.

    6. A019NRZ

      Engage the guide.

    7. Connect the No. 1 fold seat stopper band assembly with the bolt.

      9.0 N*m 92 kgf*cm 80 in.*lbf
    8. A019KLS

      Connect the rear seatback board carpet assembly RH with the 3 clips.

    9. A019LW5

      Connect the rear seatback board sub-assembly with the 2 clips.

  9. Click here

    INSPECT REAR SEAT SLIDE ADJUSTER LOCK


    1. Check that the left and right adjusters lock simultaneously when sliding the seat.

    2. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.

  10. Click here

    INSTALL REAR SEAT TRACK BRACKET COVER RH


    1. A019NBE

      Engage the 8 claws and install the 2 seat track bracket cover RH.

  11. Click here

    INSTALL REAR SEAT CENTER HEADREST ASSEMBLY


    1. A019KOM

      Install the rear seat headrest assembly as shown in the illustration.

  12. Click here

    INSTALL REAR SEAT HEADREST ASSEMBLY RH


    1. A019OYM

      Install the rear seat headrest assembly as shown in the illustration.

  13. Click here

    CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  14. Click here

    INSPECT SRS WARNING LIGHT

    (Click here)