Click here

DOOR CONTROL RELAY INSTALLATION

Click here
Click here Click here
  1. Click here

    INSTALL DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY


    1. A019K47

      Install the double lock door control relay assembly with the 2 bolts.

    2. A019MRB

      Connect the connector.

  2. Click here

    INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    1. Connect each connector.

    2. Engage the claw, 4 clips and guide.

    3. Install the glove compartment door assembly with the 5 screws <F>.

  3. Click here

    INSTALL PASSENGER SIDE KNEE AIRBAG ASSEMBLY


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A019PFU

      Connect the airbag connector to the front passenger side knee airbag assembly.

      Note:

      When connecting the airbag connector, take care not to damage the airbag wire harness.

    4. A019PG2

      Temporarily install the front passenger side knee airbag assembly with the claw.

    5. Install the front passenger side knee airbag assembly with the 3 bolts.

      10 N*m 102 kgf*cm 7 ft.*lbf
      Note:

      Confirm that the front passenger side knee airbag assembly is installed securely without any excessive gaps and is not protruding outward.

    6. A019M2BE01

      Remove the protective tape.

      Table 1. Text in Illustration
      *1 Protective Tape
  4. Click here

    INSTALL INSTRUMENT PANEL GARNISH RH (w/o Airbag Cut Off Switch)

    Tip:

    Use the same procedure as for the LH side.

  5. Click here

    INSTALL INSTRUMENT PANEL GARNISH RH (w/ Airbag Cut Off Switch)


    1. Connect the connector.

    2. A019PDB

      Engage the 6 clips to install the instrument panel garnish RH.

  6. Click here

    INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Connect the connector.

    2. A019LOA

      Engage the 2 guides and 4 claw to install the No. 2 instrument panel under cover sub-assembly.

  7. Click here

    INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

    Tip:

    Removal procedure of the RH side is the same as that of the LH side (Click here).

  8. Click here

    INSTALL FRONT DOOR SCUFF PLATE RH

    Tip:

    Removal procedure of the RH side is the same as that of the LH side (Click here).

  9. Click here

    INSTALL LOWER INSTRUMENT PANEL FINISH PANEL


    1. A019KVZ

      Engage the 7 clips to install the lower instrument panel finish panel as shown in the illustration.

  10. Click here

    INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. Engage the clamp.

    2. Connect each connector.

    3. A019MFZ

      Engage the 3 claws and 3 clips.

    4. w/o Seat Heater System:


      1. Connect the connector to the console box hole cover.

    5. w/ Seat Heater System:


      1. Connect the connector.

      2. Engage the 6 claws to install the seat heater switch with console box hole cover.

    6. A019LES

      Engage the 4 claws and 4 clips to install the upper console panel sub-assembly.

  11. Click here

    INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A019LZO

      Turn the shift lever knob sub-assembly clockwise to install the shift lever knob sub-assembly.

  12. Click here

    CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  13. Click here

    INSPECT SRS WARNING LIGHT

    (Click here)