MAYDAY BATTERY REMOVAL


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A019LPB

      Turn the shift lever knob sub-assembly counterclockwise and remove the shift lever knob sub-assembly.

  4. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A019OY8

      Move the shift lever to N.

    2. Pull the upper console panel sub-assembly in the direction indicated by the arrow to disengage the 4 claws and 4 clips.

    3. w/o Seat Heater System:


      1. Disconnect the connector from the console box hole cover.

    4. w/ Seat Heater System:


      1. A019OCZ

        Disengage the 6 claws.

      2. Disconnect the connector and remove the seat heater switch with console box hole cover.

    5. A019K0Q

      Pull the upper console panel sub-assembly in the direction indicated by the arrow to disengage the 3 claws and 3 clips.

    6. Disconnect each connector.

    7. Disengage the clamp and remove the upper console panel sub-assembly.

  5. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL


    1. A019MQD

      Pull the lower instrument panel finish panel in the direction indicated by the arrow to disengage the 7 clips and remove the lower instrument panel finish panel.

  6. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  7. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  8. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A019O27

      Disengage the 4 claws and 2 guides as shown in the illustration.

    2. Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.

  9. REMOVE INSTRUMENT PANEL GARNISH RH (w/o Airbag Cut Off Switch)

    Tech Tips

    Use the same procedure as for the LH side.

  10. REMOVE INSTRUMENT PANEL GARNISH RH (w/ Airbag Cut Off Switch)


    1. A019KUY

      Using moulding remover B, disengage the 6 clips as shown in the illustration.

    2. Disconnect the connector and remove the instrument panel garnish RH.

  11. REMOVE FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY

    CAUTION:

    When storing the front passenger side knee airbag assembly, keep the airbag deployment side facing upward.


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A019M2BE01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the front passenger side knee airbag assembly.

    4. A019PG2

      Remove the 3 bolts.

    5. Disengage the claw to separate the front passenger side knee airbag assembly.

    6. A019MJGE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver with the tip wrapped with protective tape, disconnect the airbag connector to remove the front passenger side knee airbag assembly.

      Note

      When disconnecting the airbag connector, take care not to damage the airbag wire harness.

  12. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    1. A019MLF

      Remove the 5 screws <F>.

    2. A019KKE

      Disengage the claw, 4 clips and guide.

    3. Disconnect each connector and remove the glove compartment door assembly.

  13. REMOVE MAYDAY BATTERY WITH BRACKET


    1. A019LO6

      Disconnect the connector.

    2. Remove the 2 bolts and mayday battery with bracket.

  14. REMOVE NO. 1 TELEPHONE BRACKET


    1. A019O59

      Remove the nut.

    2. Disengage the 2 guides and remove the No. 1 telephone bracket as shown in the illustration.

  15. REMOVE NO. 2 TELEPHONE BRACKET


    1. A019OFC

      Remove the No. 2 telephone bracket as shown in the illustration.

  16. REMOVE MAYDAY BATTERY