HARD DISK DRIVE REMOVAL


  1. PRECAUTION

    Note


    • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

    • A Hard Disk Drive (HDD) is built into the multimedia module receiver assembly to store map and other data, and is used for the navigation system. Therefore, care must be taken for the following points when handling the multi-media module receiver assembly.

    • When removing the hard disk drive, eliminate static electricity by touching the vehicle body to prevent components from being damaged.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A019LPB

      Turn the shift lever knob sub-assembly counterclockwise and remove the shift lever knob sub-assembly.

  4. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A019OY8

      Move the shift lever to N.

    2. Pull the upper console panel sub-assembly in the direction indicated by the arrow to disengage the 4 claws and 4 clips.

    3. w/o Seat Heater System:


      1. Disconnect the connector from the console box hole cover.

    4. w/ Seat Heater System:


      1. A019OCZ

        Disengage the 6 claws.

      2. Disconnect the connector and remove the seat heater switch with console box hole cover.

    5. A019K0Q

      Pull the upper console panel sub-assembly in the direction indicated by the arrow to disengage the 3 claws and 3 clips.

    6. Disconnect each connector.

    7. Disengage the clamp and remove the upper console panel sub-assembly.

  5. REMOVE INSTRUMENT PANEL GARNISH LH


    1. A019MAJ

      Using moulding remover B, disengage the 6 clips and remove the instrument panel garnish LH as shown in the illustration.

  6. REMOVE NO. 1 SWITCH HOLE BASE


    1. A019JWR

      Push the No. 1 switch hole base in the direction indicated by the arrow to disengage the 4 claws and 2 guides.

    2. Disconnect each connector and remove the No. 1 switch hole base.

  7. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A019N7Y

      Disengage the 2 claws and open the cover as shown in the illustration.

    2. A019KVT

      Remove the 2 screws <D>.

    3. Disengage the 8 clips and 2 guides.

    4. Disconnect each connector and remove the lower instrument panel finish panel sub-assembly.

  8. REMOVE INSTRUMENT PANEL FINISH PANEL


    1. A019PC7

      Pull the instrument panel finish panel in the direction indicated by the arrow to disengage the claw, 2 clips and 2 guides, and remove the instrument panel finish panel.

  9. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL


    1. A019MQD

      Pull the lower instrument panel finish panel in the direction indicated by the arrow to disengage the 7 clips and remove the lower instrument panel finish panel.

  10. REMOVE MULTI-MEDIA MODULE RECEIVER ASSEMBLY WITH REGISTER

    Note


    • The 4 bolts of the multi-media module receiver assembly with register are installed though the service holes at the bottom in the instrument panel. Make sure to check all of them.

    • If the multi-media module receiver assembly with register is pulled without removing the 4 bolts, it may result in damage to the multi-media module receiver assembly with register.


    1. A019OJ4E01
      Text in Illustration
      *1 Service Hole

      Remove the 4 bolts.

    2. Disengage the 7 clips.

    3. Disconnect each connector and remove the multimedia module receiver assembly with register.

  11. REMOVE HARD DISK DRIVE


    1. A019JO7

      Remove the 3 screws and No. 2 radio bracket.

    2. A019NFZ

      Remove the 2 screws.

    3. Disengage the 2 guides to remove the cover.

    4. A019O2SE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, slide the hard disk drive in the direction shown by the arrow to remove it.