NAVIGATION RECEIVER INSTALLATION


  1. PRECAUTION

    Note

    When installing the hard disk drive, eliminate static electricity by touching the vehicle body to prevent components from being damaged.

  2. INSTALL MULTI-MEDIA MODULE RECEIVER ASSEMBLY

  3. INSTALL HARD DISK DRIVE


    1. A019KSU

      Insert the hard disk drive in the direction shown by the arrow in the illustration to install it.

    2. Engage the 2 guides to temporarily install the cover.

    3. Install the cover with the 2 screws.

    4. Install the No. 2 radio bracket with the 3 screws.

  4. INSTALL NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. Engage the 5 claws to install the No. 4 instrument panel register assembly.

  5. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. Engage the 5 claws to install the No. 3 instrument panel register assembly.

  6. INSTALL HAZARD WARNING SIGNAL SWITCH ASSEMBLY (for LHD)


    1. Engage the 2 claws and install the hazard warning signal switch assembly.

    2. Engage the clamp.

  7. INSTALL HAZARD WARNING SIGNAL SWITCH ASSEMBLY (for RHD)


    1. w/o Navigation System:


      1. Engage the 2 claws and install the hazard warning signal switch assembly.

      2. Engage the 2 clamps.

    2. w/ Navigation System:


      1. Engage the 2 claws and install the hazard warning signal switch assembly.

      2. Engage the clamp.

  8. INSTALL MULTI-MEDIA MODULE RECEIVER ASSEMBLY WITH REGISTER


    1. Connect each connector.

    2. Engage the 7 clips.

    3. Install the multi-media module receiver assembly with register with the 4 bolts.

      Torque:
      4.9 N*m  { 50 kgf*cm, 43 in.*lbf }

  9. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL


    1. A019KVZ

      Engage the 7 clips to install the lower instrument panel finish panel as shown in the illustration.

  10. INSTALL INSTRUMENT PANEL FINISH PANEL


    1. A019MX7

      Engage the 2 guides, claw and 2 clips to install the instrument panel finish panel as shown in the illustration.

  11. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. Connect each connector.

    2. Engage the 8 clips and 2 guides.

    3. Install the lower instrument panel finish panel sub-assembly with the 2 screws <D>.

    4. A019NKJ

      Engage the 2 claws to close the cover as shown in the illustration.

  12. INSTALL NO. 1 SWITCH HOLE BASE


    1. Connect each connector.

    2. A019N7C

      Engage the 4 claws and 2 guides to install the No. 1 switch hole base.

  13. INSTALL INSTRUMENT PANEL GARNISH LH


    1. A019K28

      Engage the 6 clips to install the instrument panel garnish LH.

  14. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. Engage the clamp.

    2. Connect each connector.

    3. A019MFZ

      Engage the 3 claws and 3 clips.

    4. w/o Seat Heater System:


      1. Connect the connector to the console box hole cover.

    5. w/ Seat Heater System:


      1. Connect the connector.

      2. Engage the 6 claws to install the seat heater switch with console box hole cover.

    6. A019LES

      Engage the 4 claws and 4 clips to install the upper console panel sub-assembly.

  15. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A019LZO

      Turn the shift lever knob sub-assembly clockwise to install the shift lever knob sub-assembly.

  16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    CAUTION:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  17. INSPECT SUSPENSION CONTROL SYSTEM (w/ Air Suspension)

    Click here

  18. INSPECT HARD DISK DRIVE

    Click here

  19. REPLACED OPERATION

    for Parking Assist Monitor System without Side Monitor: Click here

    for Parking Assist Monitor System with Side Monitor: Click here

    for G-BOOK System without Telematics Transceiver: Click here

    for G-BOOK System with Telematics Transceiver: Click here