Click here

NAVIGATION SYSTEM, Diagnostic DTC:B15D6

Click here
Click here Click here
DTC Code DTC Name
B15D6 Display Disconnected
Click here

DESCRIPTION

The multi-media module receiver assembly and multi-display assembly are connected via AVC-LAN communication.

When an AVC-LAN communication error occurs between the multi-media module receiver assembly and multi-display assembly, this DTC will be stored.

DTC No. DTC Detection Condition Trouble Area
B15D6 Multi-display assembly is not/was not connected while the engine switch is/was on (ACC or IG).

  • Multi-display assembly power source circuit

  • AVC-LAN circuit between multi-media module receiver assembly and multi-display assembly

  • Multi-display assembly

  • Multi-media module receiver assembly

  • Harness or connector
Tip:

  • Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.

  • The multi-media module receiver assembly is the master unit.

Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Note:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


  • w/ G-BOOK System:

  • When replacing the multi-media module receiver assembly or telematics transceiver, perform vehicle contract setting (w/ Telematics Transceiver) (Click here).

  • When replacing the multi-media module receiver assembly, perform vehicle contract setting (w/o Telematics Transceiver) (Click here).

Click here

PROCEDURE


  1. Click here

    CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Check for optional components.


      1. Check that optional components (including associated wiring) which generate radio waves are not installed.

        Result
        Result Proceed to
        Optional components (including associated wiring) are installed. A
        Optional components (including associated wiring) are not installed. B
        Tip:

        • Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

        • This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.


  2. Click here

    REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Remove optional components (including associated wiring).

      Note:

      Do not remove optional components or associated wiring without the permission of the customer.


  3. Click here

    CHECK DTC


    1. Clear the DTCs (Click here).

    2. Recheck for DTCs and check that no DTCs are output.

      OK
      No DTCs are output.

  4. Click here

    CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY POWER SOURCE)


    1. Disconnect the G2 multi-display assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G2-13 (GND1) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G2-12 (+B2) - G2-13 (GND1) Always 11 to 14 V
      G2-24 (ACC) - G2-13 (GND1) Engine switch on (ACC) 11 to 14 V

  5. Click here

    CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - MULTI-MEDIA MODULE RECEIVER ASSEMBLY)


    1. Disconnect the G2 multi-display assembly connector.

    2. Disconnect the G36 multi-media module receiver assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G2-7 (TX+) - G36-45 (TX3+) Always Below 1 Ω
      G2-19 (TX-) - G36-46 (TX3-) Always Below 1 Ω
      G2-7 (TX+) - Body ground Always 10 kΩ or higher
      G2-19 (TX-) - Body ground Always 10 kΩ or higher

  6. Click here

    REPLACE MULTI-DISPLAY ASSEMBLY


    1. Replace the multi-display assembly (Click here).

    2. Clear the DTCs (Click here).

    3. Recheck for DTCs and check that no DTCs are output.

      OK
      No DTCs are output.

  7. Click here

    END

  8. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  9. Click here

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLYClick here