Click here

REAR PACKAGE TRAY SPEAKER REMOVAL

Click here
Click here Click here
  1. Click here

    PRECAUTION

    Note:

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

  2. Click here

    CONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the battery negative (-) terminal to disable the SRS system.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  3. Click here

    REMOVE DECK BOARD SUB-ASSEMBLY


    1. A019NDK

      Disengage the 3 fasteners as shown in the illustration.

    2. for Compact Spare Tire:


      1. A019N72

        Remove the 2 bolts and remove the deck board sub-assembly.

    3. for Full Size Spare Tire:


      1. A019JPE

        Remove the 2 bolts and remove the deck board sub-assembly.

  4. Click here

    REMOVE NO. 4 REAR FLOOR BOARD (for Compact Spare Tire)


    1. A019NMY

      Disengage the 2 guides and remove the No. 4 rear floor board.

  5. Click here

    REMOVE NO. 4 REAR FLOOR BOARD (for Full Size Spare Tire)


    1. A019LI6

      Disengage the 2 guides and remove the No. 4 rear floor board.

  6. Click here

    REMOVE TONNEAU COVER ASSEMBLY


    1. Remove the tonneau cover assembly.

  7. Click here

    REMOVE REAR DECK FLOOR BOX


    1. A019ODU

      Remove the 3 clips and the rear deck floor box.

  8. Click here

    REMOVE DECK SIDE TRIM BOX LH (for Compact Spare Tire)


    1. A019KNU

      Remove the 2 clips and the deck side trim box LH.

  9. Click here

    REMOVE DECK SIDE TRIM BOX LH (for Full Size Spare Tire)


    1. A019LL4

      Remove the 3 clips and the deck side trim box LH.

  10. Click here

    REMOVE FRONT DECK FLOOR BOX


    1. A019LUJ

      Remove the clip and the front deck floor box.

  11. Click here

    REMOVE REAR SEAT ASSEMBLY LH

    Tip:

    Refer to the procedure up to Remove Rear Seat Assembly LH (Click here).

  12. Click here

    REMOVE REAR DOOR SCUFF PLATE LH


    1. A019NH1

      Disengage the 6 claws, 3 clips and guide, and remove the rear door scuff plate LH.

  13. Click here

    REMOVE REAR FLOOR FINISH PLATE


    1. A019OZP

      Disengage the 2 claws, 6 clips and 2 guides, and remove the rear floor finish plate.

  14. Click here

    REMOVE REAR FLOOR FINISH SIDE PLATE LH


    1. A019NQ4

      Remove the clip.

    2. Disengage the claw and 2 clips.

    3. Disengage the guide and remove the rear floor finish side plate LH.

  15. Click here

    REMOVE REAR SEAT SIDE COVER LH


    1. A019MJQ

      Remove the 2 clips.

    2. Disengage the 2 claws and 3 clips, and remove the rear seat side cover LH.

      Tip:

      A part of the clip remains on the vehicle side.

  16. Click here

    REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. A019KWU

      Remove the No. 1 luggage compartment trim hook as shown in the illustration.

  17. Click here

    REMOVE ROPE HOOK ASSEMBLY


    1. A019MHWE01

      Using a screwdriver, disengage the 2 claws.

      Table 1. Text in Illustration
      *1 Protective Tape
      Tip:

      Tape the screwdriver tip before use.

    2. Remove the 2 bolts and the 2 rope hook assemblies.

  18. Click here

    REMOVE RECLINING REMOTE CONTROL BEZEL LH


    1. A019NFFE01

      Using moulding remover A, disengage the 2 bottom claws of the reclining remote control bezel LH.

    2. Lift the reclining remote control bezel LH as shown by the arrow (1) in the illustration.

    3. Turn the reclining remote control bezel LH as shown by the arrow (2) in the illustration, then disengage the 2 upper claws and remove the bezel.

  19. Click here

    REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Remove the 2 screws.

    2. Remove the 4 clips.

    3. Disengage the 5 claws and 2 clips.

    4. A019P1Z

      Disconnect each connector and remove the deck trim side panel assembly LH.

  20. Click here

    DISCONNECT REAR SEAT OUTER BELT ASSEMBLY LH


    1. A019MP2

      Remove the bolt and disconnect the floor end of the rear seat outer belt assembly.

  21. Click here

    REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH


    1. A019P2K

      Disengage the 8 clips.

      Tip:

      A part of the clip remains on the vehicle side.

    2. Pass the floor anchor of the rear seat outer seat belt assembly LH through the roof side inner garnish assembly LH and remove the roof side inner garnish assembly LH.

  22. Click here

    REMOVE QUARTER SIDE SPEAKER ASSEMBLY


    1. A019O6B

      Remove the 2 screws.

    2. Disconnect the connector and remove the quarter side speaker assembly.