LUGGAGE SPEAKER REMOVAL


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the battery negative (-) terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE DECK BOARD SUB-ASSEMBLY


    1. A019NDK

      Disengage the 3 fasteners as shown in the illustration.

    2. for Compact Spare Tire:


      1. A019N72

        Remove the 2 bolts and remove the deck board sub-assembly.

    3. for Full Size Spare Tire:


      1. A019JPE

        Remove the 2 bolts and remove the deck board sub-assembly.

  4. REMOVE NO. 4 REAR FLOOR BOARD (for Compact Spare Tire)


    1. A019NMY

      Disengage the 2 guides and remove the No. 4 rear floor board.

  5. REMOVE NO. 4 REAR FLOOR BOARD (for Full Size Spare Tire)


    1. A019LI6

      Disengage the 2 guides and remove the No. 4 rear floor board.

  6. REMOVE TONNEAU COVER ASSEMBLY


    1. Remove the tonneau cover assembly.

  7. REMOVE REAR DECK FLOOR BOX


    1. A019ODU

      Remove the 3 clips and the rear deck floor box.

  8. REMOVE DECK SIDE TRIM BOX LH (for Compact Spare Tire)


    1. A019KNU

      Remove the 2 clips and the deck side trim box LH.

  9. REMOVE DECK SIDE TRIM BOX LH (for Full Size Spare Tire)


    1. A019LL4

      Remove the 3 clips and the deck side trim box LH.

  10. REMOVE FRONT DECK FLOOR BOX


    1. A019LUJ

      Remove the clip and the front deck floor box.

  11. REMOVE REAR SEAT ASSEMBLY LH

    Tech Tips

    Refer to the procedure up to Remove Rear Seat Assembly LH Click here.

  12. REMOVE REAR DOOR SCUFF PLATE LH


    1. A019NH1

      Disengage the 6 claws, 3 clips and guide, and remove the rear door scuff plate LH.

  13. REMOVE REAR FLOOR FINISH PLATE


    1. A019OZP

      Disengage the 2 claws, 6 clips and 2 guides, and remove the rear floor finish plate.

  14. REMOVE REAR FLOOR FINISH SIDE PLATE LH


    1. A019NQ4

      Remove the clip.

    2. Disengage the claw and 2 clips.

    3. Disengage the guide and remove the rear floor finish side plate LH.

  15. REMOVE REAR SEAT SIDE COVER LH


    1. A019MJQ

      Remove the 2 clips.

    2. Disengage the 2 claws and 3 clips, and remove the rear seat side cover LH.

      Tech Tips

      A part of the clip remains on the vehicle side.

  16. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. A019KWU

      Remove the No. 1 luggage compartment trim hook as shown in the illustration.

  17. REMOVE ROPE HOOK ASSEMBLY


    1. A019MHWE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 2 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the 2 bolts and the 2 rope hook assemblies.

  18. REMOVE RECLINING REMOTE CONTROL BEZEL LH


    1. A019NFFE01

      Using moulding remover A, disengage the 2 bottom claws of the reclining remote control bezel LH.

    2. Lift the reclining remote control bezel LH as shown by the arrow (1) in the illustration.

    3. Turn the reclining remote control bezel LH as shown by the arrow (2) in the illustration, then disengage the 2 upper claws and remove the bezel.

  19. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Remove the 2 screws.

    2. Remove the 4 clips.

    3. Disengage the 5 claws and 2 clips.

    4. Disconnect each connector and remove the deck trim side panel assembly LH.

      A019P1Z

  20. REMOVE NO. 1 DECK BOARD REINFORCEMENT


    1. A019N3Q

      Remove the 3 bolts and No. 1 deck board reinforcement.

  21. REMOVE REAR NO. 1 SPEAKER BRACKET


    1. A019N0K

      Remove the 2 nuts and rear No. 1 speaker bracket.

  22. REMOVE REAR NO. 3 SPEAKER ASSEMBLY


    1. A019LDP

      Disconnect the connector.

    2. Remove the 3 nuts and rear No. 3 speaker assembly.